469912

Carrera DIGITAL 124-30342 Lapcounter Seite 3

3
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
8
Assembly instructions
1 4
2 3
1
+
2
+
3
Before assembling please insert the connecting clips
in the track as shown in fi gure
1
. Stick tracks together on a fl at
base. Move the connecting clips according to fi gure
2
in direction
of the arrow until they audibly snap in. The connecting clip may also
be inserted later. The connecting clips can be removed into both
directions by simply pressing down the clamped nose (see fi g.
3
).
4
Fastening: To fasten the track sections on a board, it is neces-
sary to use the track section fasteners (Item no. 85209, not con-
tained in the package).
Note:
Carpeting is not a suitable foundation on which to build the track be-
cause of static charging, formation of fl uff and ready infl ammability.
Coding/decoding of the cars to
the according speed controller
2x CLICK
1 2
2x CLICK
CK
3
Place car on the track, push lane-change-button twice fi g.
1
, lift car
at the front, put car back again fi g.
2
, while car´s lights are fl ashing
push lane-change-button twice fi g.
3
. Programming is confi rmed
by a tone. All settings are saved until new programming is carried
out.
False start
False start: If a car’s speed controller is actuated during the traffi c
light phase, this is rated as false start. The vehicle that has caused
the false start will travel a short distance and the LED on the rele-
vant vehicle or hand control will fl ash. The race is not released and
the start has to be repeated.
Display and
range of functions
1 2
3
4
Range of functions
1
Training mode
2
Lap races possible from 0 – 9999 laps (factory setting 50 laps)
3
Time races from 00:00:00’01 – 99:99:99:999 hours
(hh:mm:ss’ms) (factory setting 00:05’00’’00)
The electronic lap counter Carrera DIGITAL 124 / 132 disposes of a
memory function. Once the values of the factory setting are changed
the altered values remain displayed until having been reset.
4
Signal tone and fanfare horn may be switched on and off by ac-
tivating the switch (ON/OFF).
Training mode
1
Training mode
The training mode is used for training and the starting positions for
the race and can be started without setting the laps or time.
The training mode is set as follows:
1. Switch on the Black box (ON/OFF switch).
2. After approx. 1 second the central LED will illuminate perma-
nently and a brief acoustic signal will sound.
3. The Carrera DIGITAL 124 / 132 electronic lap counter automati-
cally switches on in training mode.
4. Press the start button of the Black Box once – all of the LEDs
are constantly lit.
5. Place the pre-coded car/s on the connecting track.
6. Then press the start button again – the starting sequence is initi-
ated, the LEDs are lit and acoustic signals can be heard.
7. The training run begins with elapse of the starting sequence and
the overall time (“TIME”) and counting begins.
8. The display shows the following information:
• Allocation of the individual cars (1-6)
• Total time of training race next to “TIME”
• Lap time currently driven “LAP TIME”
ATTENTION!
Single lap times exceeding 09:59:999 cannot be displayed, illustra-
tion see fi g.
1
.
This does not aff ect the total time illustration under
“TIME”.
While pushing BUTTON 1 during measuring, further information can
be retrieved.
• Press “BEST TIME” 1x – best lap time. Only beating the current
best time will again be displayed.
• Press “TIME” 2x – displaying the leading car (POS 1) and the other
cars´ time lag to the leading car
< 1 lap:
display of time diff erence “+ m:ss:ms” to the leading car
> 1 lap:
display of lap diff erence to the leading car “+ L 00001”
• Press “POSITION” 3x – current positioning of individual cars
• Press “LAPS” 4x – laps already driven
• Press 5x – change back to the current training race
9. For fi nishing the training race, push BUTTON 3 (“ESC”) once
during the race. You will return to the main menu (the word “TRAIN-
ING” fl ashes)
Race modes
Racing mode
1. For being able to switch to the racing mode after the electronic lap
counter Carrera DIGITAL 124 / 132 has automatically turned on via
the Black Box, please push BUTTON 3 (“ESC”).
2. The next display indication allows you to switch between the train-
ing- and the racing mode while pushing BUTTON 1 (“CHA”).
3. Confi rm selection of the racing mode (the word “Race” fl ashes) by
BUTTON 2 (“SEL”), the word “LAP” fl ashes.
4. You have the choice between
1
lap race and
2
time races.
1
Lap Races
1.
If you like to start a lap race (“LAP”) please confi rm by pushing
BUTTON 2 (“SEL”).
2.
After confi rmation you may set the number of laps you like to com-
plete (it is possible to set lap races from 0000 to 9999 laps, factory
setting 0050 laps).
3.
Basically you have to set the 1`s place fi rst, then the 10`s place
and the 100`s place and fi nally the 1000`s place (display cursor
fl ashes on each place). By pushing BUTTON 1 (“UP”) you increase
the number. In order to change to the next places please push BUT-
TON 2 (“SEL”) and set the value as described. In case the preset
number of laps shall not be changed, please confi rm by pushing
BUTTON 2 (“SEL”) until the lap display disappears.
4.
After having set the number of laps push the start button of the
Black Box once – alle LEDs will fl ash permanently.
5. Place the pre-coded car/s on the connecting track.
6. Then press the start button again – the starting sequence is initi-
ated, the LEDs are lit and acoustic signals can be heard.
7. The lap race starts after the start sequence has proceeded.
8. The total time “TIME” starts to run. Once the leading car has
passed through, its total time is displayed and updated upon each
passing.
9. The display shows the following information:
• Allocation of the individual cars (1-6)
• Total time of the leading car next to “TIME”
• Lap time currently driven “LAP TIME”
While pushing BUTTON 1 during measuring, further information can
be retrieved.
• Press “BEST TIME” 1x – best lap time. Only beating the current
best time will again be displayed
• Press “TIME” 2x – displaying the leading car (POS 1) and the
other cars´ time lag to the leading car
< 1 lap: display of time diff erence “+ m:ss:ms” to the leading car
> 1 lap: display of lap diff erence to the leading car “+ L 00001”
• Press “POSITION” 3x – current positioning of individual cars
• Press “LAPS” 4x – laps still to go
• Press 5x – change back to the current race
10. As soon as all cars have fi nished the last lap a signal indicating
the end of the race is audible and the display starts to fl ash.
11. For returning to the main menu push BUTTON 3 once („ESC“)
1
Time Racing
1. In order to measure the time of a time race please follow steps
1-3 (see lap races).
2. To start a time race after mode selection lap race (“RACE”) push
BUTTON 1 (“CHA”) for changing from the lap race mode (“LAP”) to
the time race mode (“TIME”).
3. Confi rm selection of time race (“TIME”) by BUTTON 2 (“SEL”).
4. After confi rmation the seconds´ position of the time display will
fl ash (factory setting 00:05:00 min.).
5. Basically you have to set the seconds fi rst, then the minutes
and fi nally the hours (display cursor fl ashes on each position). By
pushing BUTTON 1 (“UP”) you increase the number. In order to
change to the next positions please push BUTTON 2 (“SEL”) and
set the value as described. In case the preset racing time shall not
be changed please confi rm by pushing BUTTON 2 (“SEL”) until the
ltime display disappears.
6. After having set the requested time for the race push the start but-
ton of the Black Box once – alle LEDs will fl ash permanently.
7. Place the pre-coded car/s on the connecting track.
8. Then press the start button again – the starting sequence is initi-
ated, the LEDs are lit and acoustic signals can be heard.
9. The time race starts after the start sequence has proceeded.
10. The total time “TIME” starts to run backwards.
11. The display shows the following information:
• Allocation of the individual cars (1-6)
• Total time still to be driven “TIME”
• Lap time currently driven “LAP TIME”
While pushing BUTTON 1 during measuring, further information can
be retrieved
12. After the total time set has expired the race is fi nished. A signal
will be audible and the display starts to fl ash.
13. For returning to the main menu push BUTTON 3 once (“ESC”)
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Carrera DIGITAL 124-30342 Lapcounter wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info