470067

Carrera Digital 132 - 30154 FORMULA 1 Champions Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/7
Nächste Seite
11
Setting fuel tank capacity
Pit Stop 30346
3

1 – 10
1 – 10
(individually for one and/or several cars)
Activate fuelling function at the Black Box.
Plug any speed controller in connector 3. Switch o Black Box,
place car/s on the track, push lane-change-button and keep it
pushed while Black Box is switched on again. Don´t release the
lane-change-button until the 1st LED lights red. Fuel capacity is
set by pushing lane-change-button. Conrm by pressing speed
controller´s tappet (=> middle LED will light).
Before the start return speed controller to the original connector!
1 LED on = low fuel capacity
5 LEDs on = full tank

Depending on the fuel capacity the car´s lights start to ash after
some time, the car slows down and might start to stutter. For refuel-
ling enter the Pit Stop and release the speed controller´s tappet.
(Fuelling amount depends on car´s standing time in the Pit Stop).
a) Filling up: wait until car´s lights stop ashing.
b) Partial refuelling: start while car´s lights still ash.
c) Non-refuelling: car drives on at reduced speed.
Car programming
from DIGITAL 132
to Evolution (analogue)
Place car on the Evolution track and push speed controller´s tappet
three times (thumb). Push the switch for changing the running direc-
tion acc. g.
. For Carrera DIGITAL 132 operation mode return
the switch to original position.
Replacement of double sliding
contact and guide keel

• It is recommended to always take out and change only one
grinder.
• Never pull the vehicle backwards, because the grinders could be
damaged otherwise.
Please carefully pull out the guide keel according to g.
.
When changing the double contact brushes please take care
that in stage one the upper contact brush
is only pulled out
partly and that in stage two the double contact brush can be pulled
out completely with the contact brush
. For inserting please
proceed the same way.
Changing the rear axle
Take o the vehicle´s upper part from the chassis as per g.

Remove the axles from the bearings positions with pressure (
).
Insert new axle. Pay attention to the correct position of the axle
bearings (
).
Maintenance and care
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior to
cleaning.
 Keep the track surface and track slots clean with a
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
 Clean axle and wheel bearings, pinion gears, gear-
wheels and bearings and lubricate using a resin- and acid-free
grease. You can use a toothpick or similar as aid. Regularly check
the condition of sliding contacts and tyres.
Troubleshooting
Driving tips

In case of any malfunctions, please check the following:
• Has the connection to the power supply been established cor-
rectly?
• Have transformer and speed controllers been connected
correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track‘s current feed will be switched o automatically for 5
seconds, if there is an electrical short circuit: this will be notied by
audible and visual signals.
• Are the cars placed on the track in running direction? In case of
non-functioning push the running direction switch which is on the
car´s bottom.

During operation small car parts as spoilers or mirrors may get o or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.

• You can drive fast along the straight track but you should brake
before the curve and then accelerate again when coming out of the
curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
 When using track systems which are not manufactured by
Carrera the existing guide keel has to be replaced by the special
guide keel (#85309). While using the Carrera crossing (#20587) or
high banked curve 1/30° (#20574) slight driving noise might occur
which is due to the full-scale genuineness and does not aect aw-
less operation.
All Carrera spare parts are available in the webshop:

Delivery exclusively to Germany, Austria, Netherlands, Belgium and
Luxembourg.
Technical specifications

14,8 V
51,8 VA

1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED ashes at
long intervals.
By operating the speed controller the stand-by mode is nished,
the racetrack returns to idle-mode again.
4.) O-state = power supply unit disconnected from mains supply
This device is marked by “selective sort throught” symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized “sorting/collecting” sys-
tem in accordance with European directive 2002/96/CE, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are not
going through special collecting, are potentially dangerous for envi-
ronment and human health, because of dangerous substance.

14,8 V 42,9 VA

1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED ashes at
long intervals.
By operating the speed controller the stand-by mode is nished,
the racetrack returns to idle-mode again.
4.) O-state = power supply unit disconnected from mains supply
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Carrera Digital 132 - 30154 FORMULA 1 Champions wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info