Bedienungsanleitung Carrier 42ADF035 (Seite 16 von 35) (Englisch, Holländisch)

481320

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

42ADF025, 42ADF035

Operating Test, Address Selection and Fault Code for the Owner

Operating test

• Perform the operating test after the units have been installed in

position and the gas leak test has been completed.

• Check all electrical connections (instructions and wiring diagram).

• Insert the batteries into the remote control and leave it OFF.

• Energise the system, turning the power supply ON.

• Press the

and buttons of the infrared remote control and

hold them pressed for more than 5 seconds.

The display will be cleared, the time segments will display the

icon (Src 1 .= service test)

• Press

buttom to transmit the service test to the unit.

When test mode is selected, the unit operates as described below:

• The green LED and the orange LED blink every 2 seconds.

• The indoor fan operates at low speed.

• The louver operates according to “Auto heat” or “Auto cool” based

on operating mode.

• The system works in Cool Mode at ﬁxed compressor frequency

for 3 minutes.

• The system stops for 3 minutes.

• The system works in Heat Mode with ﬁxed compressor frequency

for 3 minutes or until the indoor coil temperature is greater than

40°C.

During the cool mode and heat mode check the following

conditions:

1. Difference between indoor ambient temperature and indoor unit

air discharge temperature must be greater than 3°C.

2. Indoor fan must operate at low speed.

3. Louver must be in auto heat or cool louver based on operating

mode.

4. No fault code must be signalled by the system.

If one of the above conditions is not positive, please check the

correct installation of the system.

• After test has been completed, press button

on the remote

control to leave the test menu.

Note:

When 30 seconds have elapsed and no buttons have been

pressed, the remote control will automatically exit the test menu

and resume its normal operation.

Address selection

If you are installing two indoor units in the same room and you want

them to operate in independent mode, it is necessary to assign

each unit its own address so that each unit can operate via its own

remote control.

For conﬁguration, proceed as follows:

Conﬁguration (of the unit)

• Press the and buttons of the infrared remote control and

hold them pressed for more than 5 seconds.

• The display will be cleared, the time segments will display

the ﬁrst conﬁguration item (rAdr = remote address) and the

temperature segments will display the default value of this

conﬁguration item (Ab = control of both indoor units).

• Press either the

or button to change the default value (Ab)

to the new value (A) or (b).

• Press

button repeatedly until “ZONE” is displayed.

• Press either the

or button to change the default value of

Zone number (0) to the new value (0÷240).

• Press

button repeatedly until “A St” is displayed.

• Press either the or button to change the default value of

auto restart in last mode (On) to the new value of start in OFF

mode(OF).

• LOOK OUT! Whichever conﬁguration value changed must be

transmitted to the indoor unit pressing

button each time.

• Press

button to leave the conﬁguration menu.

Conﬁguration (of the remote controller)

• Press the and buttons of the infrared remote control and

hold them pressed for more than 5 seconds.

• The display will be cleared, the temperature segments will display

the ﬁrst conﬁguration item (CH = remote address) and the time

segments will display the default value of this conﬁguration item

(Ab = control of both indoor units).

• Press either the

or button to change the default value (Ab)

to the new value (A) or (b).

• Press

button repeatedly until “tU” is displayed.

• Press either the

or button to change the default value of

temperatures in Degrees Celsius (C) to the new value Degrees

Fahrenheit (°F).

• Press

button repeatedly until “Hr” is displayed.

• Press either the

or button to change the default value of

Maximum heating set point temperature admitted in Degrees

Celsius (32) or Degrees Fahrenheit (90) to the new value

Degrees Celsius (17÷-32) or Degrees Fahrenheit (63÷90).

• Press

button repeatedly until “Cr” is displayed.

• Press either the

or button to change the default value of

minimum cooling set point temperature admitted in Degrees

Celsius (17) or Degrees Fahrenheit (63) to the new value

Degrees Celsius (17÷32) or Degrees Fahrenheit (63÷90).

• Press

botton repeatedly until “CL” is displayed.

• Press either the

or button to change the default value of

Time format as AM/PM (12) to the new value of 24 hours time

format (24).

• LOOK OUT! Whichever conﬁguration value changed must be

conﬁrmed pressing

button each time.

• Press

button to leave the conﬁguration menu.

Note:

When 30 seconds have elapsed and no buttons have been

pressed, the remote control will automatically exit the conﬁguration

menu and the procedure has to be restarted.

Fault code

The inside unit can detect any system fault and stop it at once.

The failure is recoverable based on the table VI below.

When a diagnostic is active, the green LED (P) and the orange LED

(R) blink 0.1 seconds on, 0.1 seconds off and indicate a fault code.

The orange LED (R) indicates the tens digits.

The green LED (P) indicates the unit digits.

Two seconds elapse between the orange LED and the green LED

lighting.

The sequence ends with both LEDs off for 4 seconds.

Example:

Fault code 13

• The orange LED blinks (it indicates the tens digits).

• Both LEDS are off for 2 seconds.

• The green LED blinks three times with a 0,5 seconds frequency.

• Both LEDS are off for 4 seconds.

The fault sequence described above is repeated until the fault has

been repaired.

If the fault code is lower than 10, the orange LED (R) is not blinking.

Carrier 42ADF035 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Carrier 42ADF035

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info