Bedienungsanleitung Carrier 42hqv035 (Seite 12 von 101) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

134526

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

EN8

4 m

The hexagon wrench

is required.

Packed valve handling precautions

• Open the valve stem all the way out, but do not try to open it beyond

the stopper.

• Securely tighten the valve stem cap with torque in the following table:

Wiring Connection

1. Remove the valve cover from the outdoor unit.

2. Connect the connecting cable to the terminals as identified with their

respective matched numbers on the terminal block of indoor and

outdoor unit.

3. When connecting the connecting cable to the outdoor unit terminals,

make a loop as shown in the installation diagram of indoor and

outdoor unit to prevent water coming in the outdoor unit.

4. Insulate the unused cords (conductors) from any water coming in the

outdoor unit. Proceed them so that they do not touch any electrical or

metal parts.

Stripping length of the connecting cable

CAUTION

• Wrong wiring connection may cause some electrical parts burn out.

• Be sure to comply with local cords on running the wire from indoor

unit to outdoor unit (size of wire and wiring method, etc.).

• Every wire must be connected firmly.

• This installation fuse (25A) must be used for the power supply line

of this air conditioner.

• If incorrect or incomplete wiring is carried out, it will cause an

ignition or smoke.

• Prepare the power supply for exclusive use with the air conditioner.

• This product can be connected to the mains.

Connection to fixed wiring: A switch which disconnects all poles

and has a contact separation of at least 3 mm must be

incorporated in the fixed wiring.

NOTE : Connecting cable

• Wire type : More than H07RN-F or 245 IEC66

Gas side 50 to 62 N·m

(∅12.70 mm) (5.0 to 6.2 kgf·m)

Gas side 30 to 42 N·m

(∅9.52 mm) (3.0 to 4.2 kgf·m)

Liquid side 16 to 18 N·m

(∅6.35 mm) (1.6 to 1.8 kgf·m)

Service port

9 to 10 N·m

(0.9 to 1.0 kgf·m)

Gas Leak Test

Check places for

the outdoor unit.

Electric parts cover

Valve cover

• Check the flare nut connections for the gas leak with a gas leak

detector or soap water.

OTHERS

How to set the Auto Restart

• Press and hold the TEMPORARY button for about 3 seconds.

After 3 seconds, the electronic beeper makes three short beeps to tell

you the Auto Restart has been selected.

• To cancel the Auto Restart, follow the steps described in the section

Auto Restart Function of the owner’s manual.

Auto Restart Setting

This product is designed so that, after a power failure, it can restart

automatically in the same operating mode as before the power failure.

Information

The product was shipped with Auto Restart function in the off

position. Turn it on as required.

Test Operation

To switch the TEST RUN (COOL) mode, press TEMPORARY button for

10 seconds. (The beeper will make a short beep.)

Model 42HQV025 42HQV035, 42HQV045

Power source 50/60Hz, 220 – 240 V Single phase

Maximum running current 8A 11A

Plug socket & fuse rating 25A

Power cord H07RN-F or 245 IEC66 (1.5 mm

or more)

Check places for

the indoor unit.

Earth line Earth line

Connecting cable

Power cord

Terminal block

30 30

40 40

TEMPORARY button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carrier 42hqv035 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info