Bedienungsanleitung Carson Reflex Wheel PRO 3 (Seite 28 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

722382

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

GB // 28

For operation, the transmitter requires 4 AA batteries or rechargea-

ble batteries or the appropriate LiPo power pack.

Once you switch on the On/Off switch, the transmitter is ready for

use.

After the transmitter has been switched on, the battery voltage will

appear in “V” on the LCD display and, below it, the model name/

number last selected will be displayed.

Settings are changed by means of the “SEL”, “CH”, “+” and “-“

buttons.

1. Press +/- to select the desired model. You have the choice of

15 memory spaces. The model number and model name are

indicated on the LCD display.

2. Press “SET” to take you to the desired setting. The following

functions are available for selection:

a) “REV” setting (reverse direction of servo rotation)

Press the “CH” button and choose between ST, TH or 3CH.

Press +/- for normal or reverse.

b) “EPA” setting (servo travel limiter)

Press the “CH” button and choose between TH or ST. To

select the direction of rotation, the throttle must be to

the front or back with TH, and the steering wheel must be

moved left or right with ST. The display shows LFU for left

and forwards and RBU for right and brake. The desired value

can be set between 0 and 120% by means of +/-.

c) ABS setting (anti-blocking system)

Press +/- for ABS on or ABS off.

d) EXP setting (exponential)

Press the “CH” button and choose between ST (steering), FW

(forwards) and BK (brake). The desired exponential value can

be set between -100% and 100% by means of +/-.

e) MODEL NAME (enter name of model)

Press the CH button until you come to the model name

setting. The characters 0 - 9 and A - Z can be entered by

means of +/-.

3. ST-TRIM (trimming the steering)

Press TRIM-ST+ or TRIM-ST- to change the neutral position

of the steering servo. It may be adjusted from 0 - 100% right

to 0 - 100% left.

4. TH-TRIMM (trimming the throttle)

Press TRIM-TH+ or TRIM-TH- to change the neutral position

of the throttle servo.

It may be adjusted from 0 -100% throttle to 0 - 100% brake.

TRIM 3C + 4C for channels 3 and 4.

5. D/R ST setting (dual rate steering)

Dual rate increases or reduces the servo travel in relation to

the travel of the steering wheel/ throttle proportionally over

the entire servo path.

Press D/R ST+ or D/R ST- to change the dual rate setting of

the steering.

A value between 0 and100% may be set.

6. D/R TH setting (dual rate throttle)

Press D/R TH+ or D/R TH- to change the dual rate setting of

the throttle.

A value between 0 and 100% may be set.

7. To close the settings, press the SEL button until the battery

display reappears.

Then the newly entered values are automatically saved.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carson Reflex Wheel PRO 3 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info