Bedienungsanleitung Casals CSS710VCE (Seite 7 von 66) (Alle Sprachen)

799647

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

Replacement of carbon brush (Fig D)

- Remove the carbon brush lid (6) with a screw-

driver.

- Replace the carbon brush.

- Install the carbon brush lid (6) with a screwdriver.

Use:

- Unroll the cable completely before plugging it in.

- Connect the appliance to the mains.

- Assemble the sanding Sheet

- Turn the appliance on, by using the on/off button

(1).

- Place the appliance against the surface you want

to work.

- Slowly move the appliance over the workpiece,

- Do not apply excessive pressure against the work-

piece.

- Apply uniform sanding pressure against the work-

piece to increase performance and working life of

the sander and the sanding sheet.

Once you have nished using the appliance:

- Stop the appliance using the on/off switch (1).

- Unplug the appliance from the mains.

- Clean the appliance.

Cleaning

- Disconnect the appliance from the mains and al-

low it to cool before undertaking any cleaning task.

- Allow it to cool before undertaking any cleaning

task.

- Clean the electrical equipment and the mains

connection with a damp cloth and dry. DO NOT IM-

MERSE IN WATER OR ANY OTHER LIQUID.

- Clean the equipment with a damp cloth with a few

drops of washing-up liquid and then dry.

- Do not use solvents, or products with an acid or

base pH such as bleach, or abrasive products, for

cleaning the appliance.

- Do not let water or any other liquid get into the

air vents to avoid damage to the inner parts of the

appliance.

- Never submerge the appliance in water or any

other liquid or place it under running water.

- If the appliance is not in good condition of cleanli-

ness, its surface may degrade and inexorably affect

the duration of the appliance’s useful life and could

become unsafe to use.

Supplies

- Always use original supplies, designed specically

for your appliance model.

- These supplies are available in specialist shops.

Anomalies and repair

- Take the appliance to an authorised technical

support service if a product damage or other

problems arise. Do not try to dismantle or repair

without assistance, as this may be dangerous.

- If the connection to the mains has been damaged,

it must be replaced and you should proceed as you

would in the case of damage.

Specifications:

CSS710VCE

- Rated power 710 W

- Rated voltage 230 V~

- No load speed 1500-3000 /min

- Sandpaper dimensions Ø 180

- Weight 2.3 Kg

- Sound Pressure level (LpA) = 90.9dB(A), KpA = 3dB

- Sound Power level (LwA) = 101.9 dB(A), KWA = 3dB

- Vibration= 2.415m/s2, K= 1,5 m/s2

NB: These specications are subject to change without

notice of purpose of improvement.

NB: By virtue of the conditions of fabrication of this

product, the maximum absorbed power can differ from

that specied.

NB: By virtue of the conditions of fabrication of this

product, the maximum used power can differ from that

specied.

Wear hearing protection

-Measured sound level determined according

EN60745

-The vibration emission level given in this information

sheet has been measured according EN60745 and

may be used to compare one tool with other. It may be

used for a preliminary assessment of exposure

-The vibration value during actual use of the power

tool can differ from the declared total value depending

on the way in which tool is used

-It’s necessary identify safety measures to protect the

operator that are based on an estimation of exposure

in the actual conditions of use (taking account of all

parts of the operating cycle such as the times when

the tool is switched off and when it is running idle in

addition to the trigger time).

For EU product versions and/or in case that it is

requested in your country:

Ecology and recyclability of the product

- Ensure that the voltage indicated on the rating label

matches the mains voltage before plugging in the ap-

pliance.

Sand paper Replacement (Fig B)

- To remove the sand paper (9) grasp it and pull it off

from the Viscid disc (8).

- Pay attention that punched holes of the sand paper

(9) match with the holes of the Viscid disc (8).

- Position the sand paper (9) ush alongside one edge

of the Viscid disc (8).

- Lay the sand paper (9) onto the Viscid disc (8) and

press rmly.

- To remove the sand paper (9) grasp it and pull it off

from the Viscid disc (8).

Replacement of Viscid disc (Fig B)

- Remove the sand paper (9).

- Block the rotation of the viscid disc (8)

- Put the allen wrench in to the hexagon hole in the

center of the viscid disc (8)

- Rotate the allen wrench clockwise

- Remove the old viscid disc (8)

- Install the new viscid disc (9)

Electronic speed control (Fig A)

- The speed of the appliance can be regulated by

using the speed regulator control (3). This function

is very useful, as it makes it possible to adapt the

speed of the appliance to the type of work that needs

to be done.

Switch on y Switch off (Fig A)

- Turn the appliance on, by pushing the on/off but-

ton (1)

- To activate the self-locking switch press the locking

button (2) while holding down the on/off button (1).

- To turn the appliance off, press the on/off button (1)

without pressing the locking button (2)

Sanding the corner (Fig C)

- Disassemble the removable lid (10) from the pad

cover (7)

- Rotate the adjust knob (11) anti-clockwise.

- Rotate the pad cover (7) until the desired position.

- Rotate the adjust knob (11) clockwise.

- Sand the corner space.

Connection set for dust outlet (Fig E)

- Connect the dust hose (13) into the dust outlet 12

- Rotate the dust hose (13) clockwise in order to lock

- Attach the cloth bag (14) to the dust hose (13)

Casals CSS710VCE Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info