Bedienungsanleitung Casio 2189 (Seite 1 von 2) (Englisch)

445424

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Module No. 2182/2189/2289 2182/2189/2289-1

GENERAL GUIDE

•Press B to change from mode to mode.

•If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.

The operational procedures for Modules 2182, 2189 and 2289 are identical. All of the illustrations in this manual show Module 2189.

Day Counter Mode Alarm ModeTimekeeping Mode Countdown Alarm Mode

Press B.

[Module 2289] [Modules 2182, 2189]

TIMEKEEPING MODE

•When using 12-hour timekeeping, a P appears on the

display for “pm” times (noon to 11:59 pm). An “am” time

(midnight to 11:59 am) is indicated when there is no P

indicator on the display. 24-hour timekeeping is being

used when the 24 indicator is on the display.

•Pressing C in the Timekeeping Mode illuminates the

display for about two seconds. The backlight is disabled

while a setting screen is on the display.

Caution

•The backlight of this watch employs an electro-lumi-

nescent (EL) light, which loses its illuminating power

after very long term use.

•Frequent use of the backlight shortens the battery life.

•The watch emits an audible sound whenever the dis-

play is illuminated. This is because the EL light vibrates

slightly when lit. It does not indicate malfunction of the

watch.

Setting the Time and Date

There are two different ways to set the time. The procedure you should use depends

on whether you want to make major changes or minor changes to the current setting.

Minutes

Seconds

Day

Day of wee

PM indicator

Hour

Month

To make major time and date settings

1.While in the Timekeeping Mode, hold down A until the seconds digits flash on the

display. This indicates the setting screen.

2.Press B to move the flashing in the sequence shown below.

Press B.

Seconds

Day

Hour Minutes

Year 12/24Month

3.While the seconds setting is selected (flashing), press C to reset it to 00.

•If you press C while the seconds setting is in the range of 30 to 59, the seconds

are reset to 00 and 1 is added to the minutes. If the seconds setting is in the range

of 00 to 29, the minutes count is unchanged.

•While the 12/24 setting is selected, press C to toggle it between 12-hour and 24-

hour timekeeping.

4.While any other digits are selected (flashing), press C to increase the selected

digits. Holding down C changes them at high speed.

5.After you make the settings you want, press A to exit the setting screen.

•The day of the week is automatically set in accordance with the date.

•The date can be set within the range of January 1, 2000 to December 31, 2039.

•When setting the year, you need to specify only the rightmost two digits. To specify

the year 2001, for example, set 01.

•The watch’s built-in full automatic calendar automatically makes allowances for dif-

ferent month lengths and leap years. Once you set the date, there should be no

reason to change it except after the replacement of the watch’s battery.

To zero-reset the minutes and seconds (EASY ADJUST)

Press D when the time on which you want to zero-reset the minutes and seconds

arrives.

•The watch beeps to let you know that the minutes and seconds were reset to 00 00.

•If you press D while the minutes count is in the range of 30 to 59, they are reset to

00 and 1 is added to the hour. If the minutes count is in the range of 00 to 29, the

hour count is unchanged.

•The watch’s EASY ADJUST feature is disabled while the daily alarm or countdown

alarm is sounding. Pressing the D button while an alarm is sounding stops the

alarm without zero-resetting the minutes and seconds.

COUNTDOWN ALARM MODE

The countdown timer can be set within a range of 1 minute

to 24 hours. When the countdown reaches zero, an alarm

sounds for 10 seconds or until you press any button.

To set the countdown time

Note that you cannot change the countdown time setting

while a countdown is being performed. First press A to

stop the countdown and then press C to return the count-

down time to its starting value.

1.Hold down A while in the Countdown Alarm Mode un-

til the hours digit flashes on the display. The hours digit

flashes because it is

selected

2.Press B to change the selection in the following se-

quence.

Press B.

Hours Minutes

3.Press C to increase the selected number. Holding down C changes the number

at high speed.

•To set the starting value of the countdown time to 24 hours, set “0:00”.

4.After you set the countdown time, press A to exit the setting screen.

To use the countdown timer

1.Press A while in the Countdown Alarm Mode to start

the countdown time.

•To stop a countdown operation, press A. Pressing A

again resumes the countdown.

•To restart the countdown, stop it and then press C to

reset to the starting value.

2.When the end of the countdown is reached, the alarm

sounds for 10 seconds or until you stop the alarm by

pressing any button. Countdown timing stops, and the

countdown time is automatically reset to its starting

value after the alarm stops.

Mode indicator

Minutes

Hours

DAY COUNTER MODE

There are five day counters, each identified by a counter number.

The initial default date for all Day Counters is 2001/1/1.

When setting the year, you need to specify only the rightmost two digits. To specify

the year 1970, for example, set 70. To specify the year 2015, set 15.

You can set the year, month, and day for a day counter, or a month and day only.

Setting a Year, Month, and Day

Setting a year, month, and day displays the number of days from the preset date to

the Timekeeping Mode date. There is no indication of whether the preset date is

before or after the Timekeeping Mode date.

•You can use this type of setting to keep track of the number of days since you were

born or the number of days you have been married, or to count down the number of

days until graduation, etc.

Setting a Month and Day Only

With this type of setting, you specify “ – – ” for the year.

The “ – – ” setting is located between the years 39 (2039)

and 40 (1940).

Setting a month and a day without a year displays the

number of days left until that month and day.

•You can use this type of setting to count down the num-

ber of days until your next birthday, etc.

Recalling Day Counter Data

In the Day Counter Mode, press C to scroll through the

day counters.

To set the target date

1.In the Day Counter Mode, press C to display the num-

ber of the counter you want to set.

2.Hold down A until the year digits start to flash on the

display. This indicates the input screen.

3.Press B to move the flashing in the sequence shown below.

Press B.

Year Month Day

4.Press C to increase the selected digits. Holding down C changes the digits at

high speed.

•Holding down B sets today as the target date. You can then make any changes in

the date you want.

5.After you make the settings you want, press A to exit the input screen.

•The date can be set within the range of January 1, 1940 to December 31, 2039.

Day counter’s number

Number of days

Year

Day

Target date

Month

Minutes

SecondsHours

Minutes

Hours

Starting value

When you want to do this:

Make major changes to the time and

date setting (before using the watch

for the first time, after having the bat-

tery replaced, etc.)

Make minor adjustments (within about

30 minutes of the current setting) to

the time setting

Use this procedure:

“To make major time and date settings”

“

To zero-reset the minutes and seconds

(EASY ADJUST

)”

Casio 2189 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 2189

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info