Operation Guide 2734 58 3748 9
2
About Auto Receive
When auto receive is turned on, the watch automatically starts to receive the time
calibration signal when the digital time in the
1:00 a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m.
will also perform an additional auto receive oper
scheduled auto receive oper
Note
• The auto receive operation is perf
Mode or
performed if a calibration time is reached while an alarm is sounding, or while you
are configuring settings (while settings are flashing on the display).
• Auto receipt of the calibration signal is designed to be perf
morning, while you sleep (provided that the
correctly).
put it in a location where it can easily receive the signal.
• When auto receive is turned on, the watch receives the calibration signal f
five minutes e
each of the calibration times.
minutes bef
correct calibration.
• Remember that reception of the calibration signal depends on the time kept in the
digital displa
shows any one of the calibr
time is actually the correct time.
• When two, three
the last reception for calibr
uses the data of the successful reception.
Receiving indicator
Weak
Strong
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
(Level 1)
(Level 4)
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being receiv
For best reception, be sure to k
strongest.
• Even in an area where signal strength is strong, it takes about 10 seconds f
signal reception to stabilize enough f
strength.
• Use the receiving indicator as a guide for checking signal strength and f
the best location for the w
• The Level 4 receiving indicator remains on the displa
reception of the time calibration signal and calibration of the w’ s time setting.
The Lev
unsuccessful or after manual adjustment of the current time setting.
• The Level 4 receiving indicator is displa
successfully receive both time and date data.
data is received.
• The Level 4 receiving indicator indicates that at least one of the calibr
receive operations w
indicator is cleared from the display at 3:00 a.m.
T
1. Place the watch on a stab
o’ clock side) is f
• Note that signal reception is poor when the 12
o’ clock side of the watch is not f
window
2. In the D for about two
seconds until the watch beeps
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Receiving indicator
3. Release D and the current time flashes to indicate that signal reception has
star
• Time calibration signal reception takes from two to fiv
do not perform any b
• After signal reception is complete, the display of the watch changes to the Last
Signal screen.
Note
• TD.
• If the receive operation is unsuccessful, the message
ERR appears on the display
for about one or tw
Mode.
• Y
ERR screen to the normal
timekeeping screen by pressing D.
T
1. In the A until the
transmitter indicator starts to flash, which indicates the
setting screen.
2. Press C three times to mov
receive on/off setting.
3. Press D to toggle auto receive on ( ON ) and off ( OF ).
• If the current Home City setting is a city code that
does not support signal receive, “xx ” appears in
place of the on/off indicator
turn auto receive on or off.
4. Press A twice to exit the setting screen.
On/off status
T
• In the TimekA to cycle through the digital time screens as
shown below
• In the TimekD to display the Last Signal screen (indicated b
GET).
calibration signal reception.
▲
Press D.
Seconds
Last Signal Screen
Receive date
Receive time
Alternate at two-
second interval
Day of week
Hour : Minutes Seconds Month — Day
A
▲
A
▲
Press A .
▲
Month — Day
▲
Signal Receive
Check the f
signal reception.
Problem
Cannot perform
manual receiv
Auto receiv
turned on, but
the Lev
receiving
indicator does
not appear on
the display
Time setting is
incorrect
follo
reception.
Probable Cause
•
The watch is not in the
• Y
follo
BER, PA, or LON.
• The transmitter setting is incorrect.
• The transmitter setting is incorrect.
• Y
• The watch was not in the
or
some button operation during the auto
receive operation.
•
Even if receiv
receiving indicator disappears ev
at 3 am.
• Time data (hour, min
was received during the last receiv
operation.
indicator appears only when time data
and date data (year
both received.
• If the time is one hour off, the DST
setting may be incorrect.
• The Home City code setting is not
correct for the area where y
the watch.
What you should do
• Enter the Timekeeping Mode
and try again.
• Select BER , PA , or LON as
your Home City
• Select the transmitter setting
appropriate for your current
location.
• Select the transmitter setting
appropriate for your current
location.
• Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
• Check to make sure the watch
is in a location where it can
receive the signal.
• Change the DST setting to
Auto DST
• Select the correct Home City
code.
• For further information, see “Important! ” under “Time Calibration Signal Reception ”
and “ Radio-controlled Timekeeping Precautions ”.
W
The
time zones) around the world.
• If the current time shown for a city is wrong, chec
Home City time settings and make the necessary
changes.
• The watch will perform a signal receive operation e
if it is in the W
reached.
settings will be adjusted in accordance with the
Timekeeping Mode’s Home City time.
• All of the operations in this section are performed in the
World C.
City Code
Current time in the
selected city code
T
While in the WD to scroll through the city codes (time zones).
• For full information on city codes, see the “City Code ”.
T
1. In the D to display the city
code (time zone) whose Standard
Saving
2. Hold down A to toggle DaDST
displayed) and Standard DST not displayed).
• Note that you cannot use the
change the DST setting of the Home City code you
currently hav
“T
setting” for information about turning the Home City
code DST setting on and off.
DST indicator
• The DST indicator is on the display whene
Daylight Sa
• Note that the DST/Standard Time setting aff
code.
Alarms
The Alarm Mode gives you a choice of f
alarms and one snooze alarm. One of the one-time
alarms functions as a “ target alarm,” which counts the
time remaining from the current Home City time to the
target alarm time.
Also use the Alarm Mode to turn the Hour
on and off.
• There are five alarms named
AL1, AL2, AL3, TAL
(target alarm), and SNZ . SNZ as
a snooze alarm only
AL1, AL2, AL3, and
TAL can be used as one-time alarms only
• Alarm settings (and Hour
availab
pressing C .
Alarm time
(Hour : Minutes)
Alarm name
Hourly Time
Signal Screen
T
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
2. After you select an alarm, hold down A until the hour setting of the alarm time
star
• This operation automatically turns on the alarm.
3. Use C to mov
4. While a setting is flashing, use D (+) and B ( –) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m.P indicator).
AL1 AL2 AL3
SIG SNZ TAL
