Operation Guide 2888
3
T
1. While the currency converter screen is displayed in the Calculator Mode
keypad to input the v
2. Press [=PM] to display the con
3. Press C to clear the conversion result.
•An E (error) indicator appears on the display when the result of a calculation
exceeds 8 digitsC to clear the error indicator
•Pressing [=PM] while a calculation result is display
again to the displayed v
T
An input tone causes the watch to beep each time you press a b
Y
•The input tone on/off setting you select in the Calculator Mode is applied to all other
modes, e
•Note that alarms will continue to sound ev
T
While the calculator screen or currency converter screen
is displayed in the Calculator ModeC fo
about two seconds to toggle the input tone on (MUTE
indicator not displayed) and off (MUTE indicator
displayed).
•Holding down C will also s
screen.
•The MUTE indicator is display
input tone is turned off.
MUTE indicator
Alarms
Y
with hour, min
turned on, the alar
reached.
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
Y
cause the watch to beep twice e
•There are five alarm screens numbered 1 through 5 .
The Hourly Time Signal screen is indicated b:00 .
•All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
Alarm time
Alarm number
Timekeeping
Mode time Alarm date
Hourly
Alarm Screen
Alarm T
The alarm type is deter
•Daily alarm
Set the hour and minutes for the alarm time.
sound everyda
•Date alarm
Set the month, day
the alarm to sound at the specific time, on the specific date you set.
•1-Month alarm
Set the month, hour and minutes for the alarm time.
alarm to sound everyday at the time y
•Monthly alarm
Set the day
to sound every month at the time y
Note
The 12-hour/24-hour format of the alarm time matches the format you select in the
Timekeeping Mode.
T
1. In the Alarm Mode, use [+] and [÷] to scroll through
the alarm screens until the one whose time you want to
set is displa
x1 x2 x3
:00 x5 x4
•Y1 as a snooze alarm or a
one-time alarm. Alarms 2 through 5 can be used as
one-time alarms only
•The snooze alarm repeats ev
2. After you select an alarm, hold down A until the left
hour setting of the alarm time star
indicates the setting screen.
•This operation automatically turns on the alarm.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Hour : Minutes
Alarm number
AM indicator
Month – Day
Press [+] Press [÷]
3. Use the keypad to input the alarm time and date.
•The flashing automatically advances to the right each time y
YB and C to move the flashing betw
•T00 for each
of the unused settings.
•If you are using 12-hour timek[=PM] while the hour or minute
setting is flashing to toggle between AM and PM.
•When setting the alarm time using the 12-hour format, take care to set the time
correctly as am (A indicator) or pm (P indicator).
4. Press A to exit the setting screen.
•Note that the month and day setting each appear as 00 on the setting screen when
no month or da
x and an unset day is shoxx . See the sample displa“ T
alarm time”.
T
In the Alarm Mode, hold down C to sound the alarm.
•Pressing C also toggles the currently displa
and off
T
2
2
2
through
5
5
5
and the Hourly
1. In the Alarm Mode, use [+] and [÷] to select a one-
time alarm (alar2 through 5 ) or the Hourly
Signal.
2. Press C to toggle it on and off
•The current on/off status of alarms 2 through 5 is
shown by indicators along the bottom of the displa
(al-2 through al-5 ).SIG indicator shows the on ( SIG
displaySIG not displayed) status of the Hourly
Time Signal.
•The alarm on indicators and Hourly Time Signal on
indicator are display
•While an alarm is sounding, the applicable alarm on
indicator flashes on the display
Alarm 2 on
indicator
Alarm 4 on
indicator
Hourly time signal
on indicator
T
1
1
1
1. In the Alarm Mode, use [+] and [÷] to select alar1 .
2. Press C to cycle through the av
sequence shown below
Snooze alarm on One-time alarm on
SNZ al-1 al-1
Alarm off
•The SNZ indicator and alarm 1 on indicator (al-1 ) are
display
•The SNZ indicator flashes during the 5-minute intervals
between alarms.
•The alarm indicator (al-1 and/or SNZ ) flashes while the
alarm is sounding.
SNZ
indicator
Alarm 1 on
indicator
SNZ indicator and alarm 1
1
1 on indicator
Press C.
Stopwatch
The stopwatch lets you measure elapsed time
and two finishes.
•The display range of the stopw
minutes, 59.99 seconds
•The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•The elapsed time measurement operation continues
ev
•Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•All of the operations in this section are performed in the
Stopwatch Mode, which yB.
Timekeeping
Mode time
Minutes
1/100 second
Seconds
Hours
T
C
Start Stop
➤
Re-start Clear
C➤
Stop
C➤ C ➤ A
Split Time
C
Start Split
➤
Split release Clear
A➤
Stop
A➤ C ➤ A
(SPL display
Start Split Stop Clear
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes. Display time of
second runner.
C➤ A ➤ C➤ A ➤ A
Elapsed Time
T
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in.
total of seven times
one-time alarm.
•Pressing any b
•P
snooze alarms cancels the current snooze alarm operation.
Displaying the
Displaying the alarm
1
setting screen
