Operation Guide 2943
3
3. When the setting you want to change is flashing, use E and B to change it as
described below
Setting
Start Time
Reset Time
Timer Mode
Screen
Button Operations
Use E (+) and B ( – ) to change the setting.
• Y
in 1-minute increments.
Use E (+) and B ( – ) to change the setting.
• Y
in 1-minute increments.
Press E to toggle between the auto-repeat mode (
)
and the elapsed time mode (
).
• An auto-repeat indicator ( A) appears when
the auto-repeat mode is selected.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4. Press A to exit the setting screen.
• The reset time setting must be less than the countdown start time setting.
T
In the Countdown C to start the
countdown timer
• The countdown timer measurement operation continues
ev
• The table below describes button oper
perform to control countdown operations
T
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and displa
Start the countdown from the displayed reset time
Do this:
Press C.
Press C again.
While the countdown is
stopped, press B.
Press B .
Press C.
T
Stop the elapsed time operation
Resume a stopped elapsed time operation
Display the countdown start time
Stop the elapsed time operation and displa
Start the countdown from the displayed reset time
Do this:
Press C.
Press C again.
While the elapsed time is
stopped, press B.
Press B .
Press C.
• The table below describes button oper
time measurement operation in the elapsed time mode
Alarms
The Alarm Mode gives you a choice of three one-time
alarms and one snooze alar
When an alarm is turned on, an aler
vibration) is performed when the alarm time is reached.
Y
SIG) that
causes the watch to beep or vibrate ev
hour.
• There are four alarms numbered
AL1 through AL3,
and
SNZ.SNZ as a snooze alarm
only
AL1 through AL3 can be used as one-
time alarms only
• All of the operations in this section are perf
Alarm Mode, which you enter by pressing D.
Timekeeping
Mode time
Alarm number
Alarm time
(Hour : Minutes)
T
1. In the Alarm Mode, use E (+) and B ( –) to scroll
through the alarm screens until the one whose time you
want to set is displa
AL1 AL2 AL3
SIG SNZ
Press
E.
Press
B.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Use D to move the flashing betw
minute settings.
4. While a setting is flashing, use E (+) and B (– ) to change it.
5. Press A to exit the setting screen.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m.P indicator).
Alarm Operation
The alert operation (beep or vibration) is performed at the preset time for about 10
seconds, regardless of the mode the watch is in.
aler
the alarm off.
• Pressing any b
• P
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the snooze alarm setting screen
T
In the Alarm Mode, hold down E to perform the currently selected Alarm Mode aler
operation.
T
1. In the Alarm Mode, use E and B to select an alarm.
2. Press C to toggle it on and off
• T
AL1, AL2, AL3)
displays the alarm on indicator on its Alarm Mode
screen.
SNZ) displays
the alarm on indicator and the snooze alarm indicator on
its Alarm Mode screen.
• In all modes, the alarm on indicator is display
alarm that is currently tur
alarm is on, the snooze alarm indicator is displayed in all
modes.
• The alarm on indicator flashes while an aler
is being performed.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Alarm on indicator
Snooze alarm indicator
T
1. In the Alarm Mode, use E and B to select the Hourly
Time Signal (
SIG
).
2. Press C to toggle it on (Hourly
indicator display
indicator not display
• The Hourly
modes when the Hourly Time Signal is turned on.
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time
and two finishes.
• The displa
minutes, 59.99 seconds
• The stopwatch contin
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues e
if you exit the Stopw
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are perf
Stopwatch Mode, which yD.
Seconds
1/100 second
MinutesHours
T
C
Start Stop
Elapsed Time
➤
Re-start Clear
C
➤
Stop
C
➤
C
➤
B
Split Time
C
Start Split
➤
Split release
Clear
B ➤
Stop
B
➤
C
➤
B
Tw
C
Start Split
➤
Stop
Clear
B ➤
Split release
C
➤
B
➤
B
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
(SPL displayed)
Illumination
The watch has an EL (electro-luminescent) panel that
causes the entire display to glo
dark. The watch’ s auto light s
illuminates the display when y
your f
• The auto light s
the auto light switch on indicator) f
• See “Illumination Precautions ” f
information about using illumination.
T
In any mode, press L to illuminate the displa
• Y
illumination duration.“T
duration” f
• The above oper
the current auto light switch setting.
Auto light switch
on indicator
About the Auto Light Switch
T
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the g
towards you at more than 40 deg
• Wear the w
Par
ground
More than
40°
Warning!
• Always make sure y
display of the watch using the auto light s
running or engaged in any other activity that can result in accident or injury
Also take care that sudden illumination b
startle or distract others around y
• When you are wearing the watch,
off before riding on a bicyc
vehicle.
distraction, whic
