Bedienungsanleitung Casio 3149 (Seite 2 von 2) (Englisch)

649157

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Operation Guide 3149

Illumination

An LED (light-emitting diode) illuminate the display for

easy reading in the dark.

Illumination Precautions

• Illumination may be hard to see when viewed under

direct sunlight.

• Illumination turns off automatically whenever an alarm

sounds.

• Frequent use of illumination runs down the battery.

To illuminate the display

Press B to turn on illumination.

Dual Time

The Dual Time Mode lets you keep track of time in a different time zone.

• In the Dual Time Mode, the seconds count is synchronized with the seconds count

of the Timekeeping Mode.

To set the Dual Time

1. Press C to enter the Dual Time Mode.

2. In the Dual Time Mode, hold down A until the hour

setting starts to flash, which indicates the setting

screen.

3. Press C to change the selection in the following

sequence.

Hour Minutes

4. Press D to increase the setting.

5. Press A to exit the setting screen.

Countdown Timer

The countdown timer can be set within a range of

1 minute to 24 hours. An alarm sounds when the

countdown reaches zero.

• You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• Countdown timer functions are available in the

Countdown Timer Mode, which you enter by pressing

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value after the alarm stops.

• Press D while a countdown operation is in progress to pause it. Press D again to

resume the countdown.

• To completely stop a countdown operation, first pause it (by pressing D), and then

press A. This returns the countdown time to its starting value.

To set the countdown start time

1. In the Countdown Timer Mode, hold down A until the

hours setting of the countdown start time starts to flash,

which indicates the setting screen.

2. Press C to move the flashing between the hours and

minutes settings.

3. While a setting is flashing, use D to change it.

• To set the starting value of the countdown time to

24 hours, set

0:00

4. Press A to exit the setting screen.

To turn auto-repeat on and off

1. In the Countdown Timer Mode, hold down A until the

hours setting of the countdown start time starts to flash,

which indicates the setting screen.

2. Press B to toggle auto-repeat on (

AUTO REPEAT

displayed) and off (

AUTO REPEAT

not displayed).

• Note that pressing B in the above operation also turns

on the illumination.

• When the end of the countdown is reached while

auto-repeat is on, the alarm sounds, but the countdown

restarts from the beginning without stopping. You can

stop the countdown by pressing D and manually reset

to the start time by pressing A.

• The auto-repeat indicator appears in the Countdown

Timer Mode only.

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

• The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

To measure times with the stopwatch

Elapsed time

Start Stop Re-start Stop Clear

Start

Split

(SPL displayed)

Split release Stop Clear

Start

Split Stop Split release Clear

Split time

Two Finishes

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

To turn the hourly time signal on and off

1. In the Alarm Mode, use D to select the hourly time

signal (

:00

2. Press A to toggle it on and off.

• Turning on the hourly time signal displays the hourly

time signal on indicator.

• The hourly time signal on indicator is displayed in all

modes when the hourly time signal is turned on.

Hour

Minutes

Seconds

Hourly time signal on

indicator

Auto-repeat indicator

1/100 second

Hour

Minutes

Seconds

Hour : Minutes Seconds

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Auto return features

• If you leave a screen with flashing digits for two or three minutes without performing

any operation, the watch automatically saves any settings you have made up to that

point and exits the setting screen.

Data and Setting Scrolling

The D button is used to scroll through setting screen data on the display. Holding

down this button during a scroll operation scrolls through the data at high speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio 3149 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 3149

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info