Bedienungsanleitung Casio 3199 (Seite 2 von 3) (Englisch)

536089

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Operation Guide 3199

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Hours Minutes

Seconds

3. When the setting you want to change is flashing, use D (+) and B (–) to change

the flashing item.

• To specify a countdown start time of 24 hours, set

4. Press A to exit the setting screen.

To use the countdown timer

Press D while in the Countdown Timer Mode to start the

countdown timer.

• When the end of the countdown is reached, the alarm

sounds for ten seconds or until you stop it by pressing

any button. The countdown time is reset to its starting

value automatically when the alarm sounds.

• Press D while a countdown operation is in progress to

pause it. Press D again to resume the countdown.

• To stop a countdown operation completely, first pause it

(by pressing D), and then press A. This returns the

countdown time to its starting value.

Countdown Timer

The countdown timer can be set within a range of one

second to 24 hours. An alarm sounds when the

countdown reaches zero.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the alarm number you want to set is

displayed.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

• This operation turns on the One-time Alarm automatically.

3. Press C to move the flashing in the sequence shown below to select other settings.

Hour Minutes

One-time Alarm/Daily Alarm Selection

Alarms

Your watch has a total of five alarms, each of which you

can configure as a daily alarm or one-time alarm.

• Daily Alarm: Sounds at the preset time each day.

• One-time Alarm: Sounds once at the preset time and

then is disabled automatically.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

• All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

• Alarms operate in coordination with the current Home

City Time.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D (east) to display the

city code (time zone) whose Standard Time/Daylight

Saving Time setting you want to change.

2. Hold down A for about one second to toggle Daylight

Saving Time (DST displayed) and Standard Time (DST

not displayed).

• The DST indicator is on the display whenever you

display a city code for which Daylight Saving Time is

turned on.

• Note that the DST/Standard Time setting affects only the

currently displayed city code. Other city codes are not

affected.

• Note that you cannot switch between Standard Time

and Daylight Saving Time while UTC is selected as the

city code.

To change your Home Time city to the current World Time city

1. In the World Time Mode, use D to display the city you want to make your new

Home Time city.

2. Press A and B at the same time.

• This makes the World Time city you selected in step 1 your new Home Time city.

World Time

World Time shows the current time in 48 cities (31 time

zones) around the world.

• All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

To view the time for another city code

In the World Time Mode, press D to scroll eastwardly

through city codes.

• For full information about city codes, see the “City Code

Table”.

• If the current time for a city is wrong, check your

Timekeeping Mode time and time zone settings and

make the necessary changes.

Changing Your Home City Time

Use the following procedure to change your current Home City Time to any one of the

three Local Times.

1. In the Timekeeping Mode, press D to display the Local Time which you want to

make your Home City Time.

2. Press A and B at the same time.

• This makes the Local Time you selected in step 1 your new Home City Time.

Illumination

An LED (light-emitting diode) illuminate the display for easy reading in the dark.

Illumination Precautions

• The illumination provided by the light may be hard to see when viewed under direct

sunlight.

• Illumination automatically turns off whenever an alarm sounds.

• Frequent use of illumination runs down the battery.

To turn on illumination

In any mode (except when a setting screen is on the display), press B to turn on

illumination.

• You can use the procedure above to select either 1.5 seconds or 3 seconds as the

illumination duration. When you press B, the illumination will remain on for about

1.5 seconds or 3 seconds, depending on the current illumination duration setting.

DST indicator

Current time and date in

the zone of the selected

city code

City code

Alarm time

(Hour : Minutes)

Alarm number

Alarm on indicator

Screen

To do this:

Change the hour

and minutes.

Toggle between

One-time Alarm

and Daily Alarm.

Do this:

Use D (+) and B (–).

• With the 12-hour format, set the time correctly as a.m.

or p.m. (P indicator).

Press D.

One-time Alarm on:

Daily Alarm on:

4. While a setting is flashing, use D and B to change it as described below.

5. Press A to exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in.

• Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

• To stop the alarm tone after it starts to sound, press any button.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to cycle through the alarm settings as shown below.

Daily Alarm On

One-Time Alarm

Alarm Off

• In all modes, the alarm on indicator is shown for the alarm that is currently turned

on.

• The alarm on indicator flashes while the alarm is sounding.

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal.

2. Press A to toggle it on and off.

• The Hourly Time Signal on indicator is shown on the

display in all modes while this function is turned on.

Seconds

1/10 second

Hours

Minutes

Hourly time signal

on indicator

Casio 3199 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 3199

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info