552992

Casio 3263 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
2
Operation Guide 3263
To toggle the Timekeeping Mode time between DST and Standard Time
Use 1. D to display the current Home City Time (T-1)
screen.
Hold down 2. A until the seconds start to flash, which
indicates the setting screen.
Press 3. C to display the DST setting screen.
Press 4. D to toggle between Daylight Saving Time
( displayed) and Standard Time ( displayed).
Press 5. A to exit the setting screen.
The •DST indicator appears on the Timekeeping screen to
indicate that Daylight Saving Time is turned on.
DST indicator
12/24-Hour Format
With the 12-hour format, the •P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without •
any indicator.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is •
applied in all other modes.
Changing the City Setting of a Local Time
You can select any one of the city codes in the table at the back of this manual as a
Local Time city.
Display the Local Time whose city setting you want to change, and then hold down 1.
A for about one second until the current city code starts fo flash.
Use 2. D (east) and B (west) to select the city code you want.
Press 3. C to display the DST setting screen.
Press 4. D to toggle between Daylight Saving Time ( displayed) and Standard
Time ( displayed).
After the settings are the way you want, press 5. A.
Swapping the Home City Time with a Local Time
You can use the procedure below to swap the current Home City Time (T-1) with one
of the Local Times (T-2, T-3, T-4).
In the Timekeeping Mode, use 1. D to display the Local Time that you want to swap
with the Home City Time.
Press 2. A and B at the same time.
World Time
World Time shows the current time in 48 cities (31 time
zones) around the world.
All of the operations in this section are performed in the •
World Time Mode, which you enter by pressing C.
To view the time for another city code
In the World Time Mode, press D to scroll eastwardly
through city codes.
For full information about city codes, see the “City Code •
Table”.
If the current time for a city is wrong, check your •
Timekeeping Mode time and time zone settings and
make the necessary changes.
City code
Current time and date in
the zone of the selected
city code
To toggle a city code time between Standard Time and Daylight Saving Time
In the World Time Mode, use 1. D (east) to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
Hold down 2. A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
The •DST indicator is on the display whenever you display
a city code for which Daylight Saving Time is turned on.
Note that the DST/Standard Time setting affects only •
the currently displayed city code. Other city codes are
not affected.
Note that you cannot switch between Standard Time •
and Daylight Saving Time while UTC is selected as the
city code.
To change your Home Time city to the current World Time city
In the World Time Mode, use 1. D to display the city you want to make your new
Home Time city.
Press 2. A and B at the same time.
This makes the World Time city you selected in step 1 your new Home Time city. •
Alarms
Your watch has a total of five alarms, each of which you
can configure as a daily alarm or one-time alarm.
Daily Alarm: Sounds at the preset time each day. •
One-time Alarm: Sounds once at the preset time and then •
is disabled automatically.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
All of the operations in this section are performed in the •
Alarm Mode, which you enter by pressing C.
Alarms operate in coordination with the current Home •
City Time.
DST indicator
Alarm on indicator
Alarm number
Alarm time
(Hour : Minutes)
To set an alarm time
In the Alarm Mode, use 1. D to scroll through the alarm
screens until the alarm number you want to set is
displayed.
After you select an alarm, hold down 2. A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
This operation turns on the One-time Alarm automatically. •
Press 3. C to move the flashing in the sequence shown below to select other
settings.
Hour Minutes
One-time Alarm/Daily Alarm Selection
While a setting is flashing, use 4. D and B to change it as described below.
Screen To do this: Do this:
Change the hour and
minutes. Use D (+) and B (–).
With the 12-hour format, set the time correctly •
as a.m. or p.m. (P indicator).
/Toggle between One-
time Alarm and Daily
Alarm.
Press D.
One-time Alarm on:
Daily Alarm on:
Press 5. A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the
watch is in.
Alarm and Hourly Time Signal operations are performed in accordance with the •
Home City Time (T-1).
To stop the alarm tone after it starts to sound, press any button. •
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
In the Alarm Mode, use 1. D to select an alarm.
Press 2. A to cycle through the alarm settings as shown below.
Alarm Off One-Time Alarm
On
Daily Alarm On
In all modes, the alarm on indicator is shown for the alarm that is currently turned •
on.
The alarm on indicator flashes while the alarm is sounding. •
To turn the Hourly Time Signal on and off
In the Alarm Mode, use 1. D to select the Hourly Time
Signal.
Press 2. A to toggle it on and off.
The Hourly Time Signal on indicator is shown on the •
display in all modes while this function is turned on.
Hourly time signal on
indicator
Countdown Timer
The countdown timer can be set within a range of one
second to 24 hours. An alarm sounds when the countdown
reaches zero.
All of the operations in this section are performed in the •
Countdown Timer Mode, which you enter by pressing C.
Minutes
Hours
Seconds
1/10 second
To configure the countdown timer
While the countdown start time is on the display in the 1.
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
If the countdown start time is not displayed, use the •
procedure under “To use the countdown timer” to
display it.
Press 2. C to move the flashing in the sequence shown
below to select other settings.
Hours Minutes Seconds
When the setting you want to change is flashing, use 3. D (+) and B (–) to change
the flashing item.
To specify a countdown start time of 24 hours, set •.
Press 4. A to exit the setting screen.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio 3263 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Casio 3263

Casio 3263 Bedienungsanleitung - Deutsch - 5 seiten

Casio 3263 Bedienungsanleitung - Holländisch - 4 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info