Bedienungsanleitung Casio 3437 (Seite 2 von 5) (Englisch)

694967

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Operation Guide 3437

E-19

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the alarm number you want to set is

displayed.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to ﬂ ash, which indicates the setting screen.

x This operation turns on the One-time Alarm automatically.

E-18

Alarms

Your watch has a total of ﬁ ve alarms, each of which you

can conﬁ gure as a daily alarm or one-time alarm.

x Daily Alarm: Sounds at the preset time each day.

x One-time Alarm: Sounds once at the preset time and then

is disabled automatically.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

x All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C (page E-5).

x Alarms operate in coordination with the current Home

City Time.

Alarm on indicator

Alarm number

Alarm time

(Hour : Minutes)

E-17

To change your Home Time city to the current World Time city

1. In the World Time Mode, use D to display the city you want to make your new

Home Time city.

2. Press A and B at the same time.

x This makes the World Time city you selected in step 1 your new Home Time city.

E-16

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D (east) to display the city

code (time zone) whose Standard Time/Daylight Saving

Time setting you want to change.

2. Hold down A for about one second to toggle Daylight

Saving Time (DST displayed) and Standard Time (DST

not displayed).

x The DST indicator is on the display whenever you display

a city code for which Daylight Saving Time is turned on.

x Note that the DST/Standard Time setting affects only

the currently displayed city code. Other city codes are

not affected.

x Note that you cannot switch between Standard Time

and Daylight Saving Time while UTC is selected as the

city code.

DST indicator

E-15

World Time

World Time shows the current time in 48 cities (31 time

zones) around the world.

x All of the operations in this section are performed in

the World Time Mode, which you enter by pressing C

(page E-4).

To view the time for another city code

In the World Time Mode, press D to scroll eastwardly

through city codes.

x For full information about city codes, see the “City Code

Table” at the back of this manual.

x If the current time for a city is wrong, check your

Timekeeping Mode time and time zone settings and

make the necessary changes.

City code

Current time and date in

the zone of the selected

city code

E-14

To turn on illumination

In any mode (except when a setting screen is on the display), press B to turn on

illumination.

x You can use the procedure above to select either 1.5 seconds or 3 seconds as the

illumination duration. When you press B, the illumination will remain on for about

1.5 seconds or 3 seconds, depending on the current illumination duration setting.

E-13

Changing Your Home City Time

Use the following procedure to change your current Home City Time to any one of the

three Local Times.

1. In the Timekeeping Mode, press D to display the Local Time which you want to

make your Home City Time.

2. Press A and B at the same time.

x This makes the Local Time you selected in step 1 your new Home City Time.

Illumination

An LED (light-emitting diode) illuminate the display for easy reading in the dark.

Illumination Precautions

x The illumination provided by the light may be hard to see when viewed under direct

sunlight.

x Illumination automatically turns off whenever an alarm sounds.

x Frequent use of illumination runs down the battery.

E-12

12/24-Hour Format

x With the 12-hour format, the PM indicator appears for times in the range of noon to

11:59 p.m. and no indicator appears for times in the range of midnight to 11:59 a.m.

x With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

x The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Changing the City Setting of a Local Time

You can select any one of the city codes in the table at the back of this manual as a

Local Time city.

1. Display the Local Time whose city setting you want to change, and then hold down

A for about two seconds until the current city code starts to ﬂ ash.

2. Use D (east) and B (west) to select the city code you want.

3. Press C to display the DST setting screen.

4. Press D to toggle between Daylight Saving Time (

displayed) and Standard

Time (

displayed).

5. After the settings are the way you want, press A.

E-11

To toggle the Timekeeping Mode time between DST and Standard Time

1. Use D to display the current Home City Time (T-1)

screen.

2. Hold down A until the seconds start to ﬂ ash, which

indicates the setting screen.

3. Press C to display the DST setting screen.

4. Press D to toggle between Daylight Saving Time (

displayed) and Standard Time (

displayed).

5. Press A to exit the setting screen.

x The DST indicator appears on the Timekeeping screen to

indicate that Daylight Saving Time is turned on.

DST indicator

E-10

5. Press A to exit the setting screen.

x The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

Casio 3437 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 3437

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info