Operation Guide 3779 4306
2
About Auto Receive
With auto receive, the w
five times a da
operations are not perf
your currently selected Home
Saving
Y Auto Receive Start
1
GMT +0 Standard 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
Daylight Saving 2:00 am 3:00 am 4:00 am 5:00 am Midnight
GMT +1 Standard 2:00 am 3:00 am 4:00 am 5:00 am Midnight
Daylight Saving 3:00 am 4:00 am 5:00 am Midnight 1:00 am
next da
GMT +2 Standard 3:00 am 4:00 am 5:00 am Midnight 1:00 am
next da
Daylight Saving 4:00 am 5:00 am Midnight 1:00 am 2:00 am
next da next da
GMT –5, Standard Midnight 1:00 am 2:00 am 3:00 am 4:00 am
–6, Daylight Saving Time
–7,
–8
Note
•When a calibration time is reached, the w
calibration signal only if it is in either the
Mode.
configuring settings.
•Auto receipt of the calibr
morning, while you sleep (provided that the
Before going to bed f
location where it can receive the signal easily
•The watch receiv
the time in the
perform any button oper
calibration times.
•Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode.
shows any one of the calibr
time is actually the correct time.
T
1. In the B for about fiv
seconds until the second hand mov
selected time zone and stops.
2. Press A a many times as required to mov
hand to 11 o’clock.
•Time calibration signal reception is turned off when
the second hand is pointing to 11 o’clock.
3. Press B three times to exit the setting mode
•If you turn off signal reception and then select a home
time zone that supports signal reception again, be sure
to perform a manual receiv
setting.
T
1. Place the watch on a stable surf’ clock side
is facing to
2.A for about two
seconds until the second hand mov
the bottom of the f“• ” (33 seconds).
•This will start manual calibration signal reception.
3.
conditions described below during signal reception.
•The hour and minute hands continue to keep time
normally
Start of Signal
Reception
“• ” area (33 seconds)
“••• ” area (38 seconds)
Getting ready
to receive
Receiving
It means this:If the second hand is pointing here:
•Time calibration signal reception takes from tw
cases it can take up to 10 minutes
operations or mov
•The watch will enter the Receiv
complete.
•TA.
Viewing the Latest Signal Reception Results
Y
correctly
T
Enter the Receive Result Mode.
•The watch will enter the Receiv
automatically after you perf
operation.
•The position of the second hand indicates the result of
the latest receive operation, as sho
“Y ” area (22 seconds) :
“N ” area (27 seconds) :
•The hour and minute hands continue to k
•The watch will not enter the Receive Result Mode when yA if calibration
signal reception is turned off.
•TA.
•Manually changing the hour and minute hand setting clears the current receiv
result.“N ” area (27 seconds).
•The second hand will point to the “ N ” area (27 seconds) if the last receive operation
was interrupted for some reason.
Signal Reception
Check the follo
•The watch is not in the
Mode or Receive Result Mode
•Signal reception is turned off.
•Y
manually
•
Y
when the auto receiv
were reached.
•
Y
A
while signal receive
was in progress
Cannot
perform
manual
receive.
The second
hand is
pointing to
the “ N ” area
(
27 seconds
).
•Enter the
or Receive Result Mode and
try again.
•Select a time zone that
enables calibration signal
reception.
•P
receive or wait until the ne
auto signal receive operation
is performed.
•Check to mak
watch is in a location where it
can receive the signal.
What you should doProblem Probab
Time setting
is incorrect
follo
signal
reception.
•The Home Time Zone setting is not
correct for the area where y
using the watch.
•The home position of the hands is
off.
•Select the correct Home
Time Zone.
•Enter the Home P
Adjustment Mode and adjust
the home position.
•For further information, see “ Important! ” under “Time Calibration Signal Reception ”
and “Radio-controlled Timekeeping Precautions ”.
Adjusting the Home P
If the time settings are wrong ev
normally
T
1. Enter the Home P
•If the home position of the second hand is currently
correct, it will mov’ clock position.
•The analog hands do not keep time during home
position adjustment.
2. Check the position of the second hand.
•The second hand home position is correct if it is
pointing at 12 o’clock.
•If the second hand is not pointing at 12 o ’clock, it
means that its home position is off.
press A to mov
second steps, until it points at 12 o’clock.
12 o’ clock
Correct second hand
home position 3. Press B to adv
position adjustment.
•If current hour and minute hand alignment is correct,
they will both mo’clock.
4. Check the position of the hour and min
•If the hour and minute hands are not pointing at 12
o’ clock, it means that their home position is off
happens, press A to mov
hands clockwise in 20-second steps
at 12 o’clock.
5. Press B to e
•This will cause the watch to return to the
Mode.
the current time.
Correct hour
and minute hand
home position
12 o’ clock
Timekeeping
Use the
time.
manually
•If you become confused and lose your w
following procedures
not perform any b
minutes.
Timekeeping Mode (indicated by normal one-second
movement of the second hand) automatically
you can try performing the manual setting procedure
again from the beginning.
Hour hand Minute hand
Second hand
Setting the
Y
Standard
•Y
T
1. In the B for about fiv
seconds until the second hand moves to the currently
selected time zone and stops.
2. Press B twice.
•This will cause the second hand to the 8-second
position.
3.
Press
A
to move the time setting f
•Holding down A f
speed hand movement.
will continue until the hands complete a 12-hour cycle,
or until you stop them bA .
4. Coordinating with a time signal on the radio or B to restart nor
timekeeping.’ clock at the start of timekeeping.
•If you did not change any of the time settings (hourB will cause
the second hand to mov
timekeeping from there.
•If you manually change the time setting between midnight and noon, the w
perform auto receive starting from noon.
the normal times (star
setting between noon and midnight, the watch will start performing normal auto
receive starting from midnight.
