Operation Guide 4335 4348
2
• The lunitidal interval is the time elapsing between the Moon’s transit over a meridian
and the next high tide at that meridian. See “Lunitidal Interval” for more information.
• This watch displays lunitidal intervals in terms of hours and minutes.
• The “Site/Lunitidal Interval Data List” provides UTC differential and longitude
information around the world.
• The following is the initial factory default Home Site data (T
first purchase the watch and whenever you have the batteries replaced. Change
these settings to match the area where you normally use the watch.
UTC differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
20 minutes)
To configure Home Site data
1. In the TA until the
seconds start to flash, which indicates the setting
screen.
2. Press C once to display the UTC differential setting
screen, and confirm that the setting is correct.
• If the UTC differential setting is not correct, use D (+)
and B (–) to change it.
3. Press A to display the longitude value setting screen.
4. Press C to move the flashing in the sequence shown
below to select other settings.
5. While the setting you want to change is flashing, use D and B to change it as
described below
Lunitidal Interval
Hours
Lunitidal Interval
Minutes
Longitude
(East/West)
Longitude
Va
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Longitude
Value
Longitude
(East/West)
Setting
Longitude V
Longitude
(East/West)
Lunitidal Interval
Hours, Minutes
Button Operations
Use D (+) and B (–) to change the setting.
• You can specify a value from 0˚ to 180˚ , in 1-
degree units.
Use D to switch between east longitude ( E )
and west longitude (
).
Use D (+) and B (–) to change the setting.
Screen
6. Press A to exit the setting screen.
Setting the Analog T
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display
To adjust the analog time
1. In the TC seven times to
enter the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D to adjust the analog setting.
• Press D once to advance the hands 20 seconds.
• Hold down D to advance the hands at high speed.
• To lock high speed hands movement, hold down D to start it and then press B
to lock. The hands will continue to advance for one 12-hour cycle or until you
press any button to stop it.
It will also stop automatically after the time advances 12 hours or if an alarm (daily
alarm, Hourly T
4. Press A to exit the setting screen.
• The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
• Toreturn to the C.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Tide/Moon Data
Tide/Moon data lets you view the Moon age and the Moon
phase for a particular date, and tidal movements for a
particular date and time for your Home Site.
• When you enter the T
6:00 a.m. on the current date appears first.
• If you suspect that the T
some reason, check the Timekeeping Mode data
(current time, date, and Home Site settings), and make
changes as required.
• See “Moon Phase Indicator” for information about the
Moon phase indicator and “T
about the tide graph.
• All of the operations in this section are performed in the
Tide/Moon Data Mode, which you enter by pressing C.
Month – Day
Time
Tide graph
Moon Phase Indicator
Tide/Moon Data Screens
In the Tide/Moon Data Mode, press A to toggle between the Tide Data screen and
the Moon Data screen.
• When you enter the T
data (Moon age and Moon phase indicator) for the current date as kept by the
Timekeeping Mode.
Press A .
▲
Moon Data Screen
▲
Moon age
Moon phase indicator
Tide Data Screen
Tide graph
Time
Month – Day
To view the Moon data for a particular date
1. In the TA to display the Moon Data screen.
2. Use D (+) and B (–) to display the date whose Moon Data you want to view
• You can select any date from 2000 to 2099.
• You can also specify a date for tide data or Moon data. For details, see “T
date”.
To view tide data for a particular time
1. In the TA to display the Tide Data screen.
• The initial screen shows the tide graph for 6:00
2. Use D (+) and B (–) to display the time whose T
To specify a date
1. In the TA until the
year setting starts to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select the other settings.
Month DayYear
3. While a setting is flashing, use D (+) or B (–) to
change it.
• You can specify a date in the range of January 1,
2000 to December 31, 2099.
4. Press A to exit the setting screen.
5. Use A to display either the T
Moon Data screen.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Year
Month – Day
Thermometer
This watch uses a temperature sensor to measure temperature.
during each even-numbered minute, and the result of the last reading is displayed on
the thermometer screen.
The watch also takes separate readings and stores them in memory for display in the
temperature tendency graph, which can be viewed in the T
Measured temperature values are stored in memory for later recall when you need
them.
Press A .
▲
▲
Thermometer Screen
Thermometer
Temperature
Tendency Screen
Temperature
Tendency
Graph
• You can select either Celsius (° C) or Fahrenheit (° F) units for the thermometer
screen. See “T
• The thermometer screen displays temperature values in 0.1 °C units (or 0.2 °F units).
• The display range of the thermometer screen is –10.0 °C to 60.0 °C (or 14.0 °F to
140.0° F).
• You can calibrate the temperature sensor if you feel that the displayed temperature
values are not correct. See “T
Important!
• Temperature measurements are affected by your body temperature (while you are
wearing the watch), direct sunlight, and moisture. T
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe all moisture from the case. It takes
approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.
Temperature T
The watch also takes temperature readings at the top and the bottom of each hour
and stores the results in memory for display on the temperature tendency graph.
Depending on the current T
shows either the top of the hour measurements or the bottom of the hour
measurements for the past 17 hours.
From the top of each hour to the 29th minute, past top of the hour readings are shown
in the graph. From the bottom of each hour to the 59th minute, past bottom of the hour
readings are shown in the graph.
Temperature tendency graph contents are updated every 30 minutes.
Past 17 hours of
measurement values
Latest measurement value
+6.0 to +9.9° C (+10.8 to +17.9°F)
+2.0 to +5.9° C (+3.6 to +10.7°F)
–1.9 to +1.9°C (–3.5 to +3.5 °F)
–5.9 to –2.0°C (–10.7 to –3.6 °F)
–9.9 to –6.0°C (–17.9 to –10.8 °F)
▲
l
l
l
l
l
l
l
l
l
Temperature change greater
than +10.0
°
C (+18.0
°
F)
Temperature change greater
than –10.0
°
C (–18.0
°
F)
Error
The horizontal axis of the graph represents time. The rightmost column is the newest
temperature value in memory
stored approximately 17 hours ago (1 dot = 1 hour). The vertical axis of the graph
represents the relative change from one hour to the next.
• When the relative change from one hour to the next exceeds +10.0ºC (+18.0ºF), the
dot at the highest point for the applicable hour flashes.
• When the relative change from one hour to the next exceeds –10.0ºC (–18.0ºF),
there is no dot in the applicable hour's column.
• If a measurement error occurs for some reason, only a single the dot in the center
column will be displayed.
