Operation Guide 4732 4733
4
T
1. In the D to display the city code
(time zone) whose Standard
setting you w
2. Hold down A to toggle between Da
(DST indicator displaDST
indicator not displa
• The DST indicator is shown on the
while Daylight Sa
• Note that changing the Daylight Sa
code causes the setting to be applied to all city codes.
DST indicator
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow f
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch to
face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) f
• See “ Illumination Precautions ” for other important
information about using illumination.
T
In any mode (except when a setting screen is on the
display), press B to illuminate the displa
second.
• The abov
the current auto light switch setting.
Auto light switch
on indicator
About the Auto Light Switch
T
your wrist as described below in any mode, e
screen.
Moving the watch to a position that is parallel to the g
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of y
Parallel to
ground
More than
40°
Warning!
•
•
• Always make sure y
display of the watch using the auto light s
running or engaged in any other activity that can result in accident or injury
Also take care that sudden illumination b
startle or distract others around y
•
•
• When you are wearing the watch,
off before riding on a bicyc
vehicle.
distraction, whic
T
In the D for about three seconds to toggle the auto
light switch on (auto light s
indicator not display
• The auto light switch on indicator is on the displa
switch is turned on.
• In order to protect against running down the battery
automatically approximately six hours after y
procedure to turn the auto light switch back on if y
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below
Module 4732 Module 4733
Moon phase indicator
0.0 - 1.8
1.9 - 5.5 5 9 1
16.7 - 20.2
20.3 - 23.9 24.0
27.7 - 29.5
• The Moon phase indicator shows the Moon as vie
Nor
Moon phase indicator may diff
• The left-right orientation of the Moon phase is rev
Southern Hemisphere or from a point near the equator.
Moon
Phase
Indicator
Moon Age
Moon Phase
New
Moon
First
Quarter
(W
Full
Moon
Last
Quarter
(Waning)
Moon phase (part you can see)
(part you cannot see)
Module
4732
Module
4733
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle.
appears to wax and wane as the relativ
changes.
we see illuminated.
*
Ear
This watch performs a rough calculation of the current Moon age starting from day 0
of the moon age cycle.
only (no fractions), the margin for error of the displa
Thermometer
Temperature Sensor Calibration
The temperature sensor built into the watch is calibr
requires no further adjustment. If you notice serious errors in the temper
produced by the watch, y
Important!
Incorrectly calibrating the temperature sensor can result in incorrect readings.
Carefully read the following bef
•
Compare the readings produced by the w
accurate thermometer
•
If adjustment is required, remove the w
minutes to give the temper
T
1.A until the
seconds star
screen.
2.C nine times to display the temperature sensor
calibration screen.
3.D (+) and B ( – ) to change the calibration v
• Y° C (0.2° F) steps, in a
range of ±10° C (±18 ° F).
‘‘--. - ’’ when the setting is outside the allow
• T‘‘- - ’’),
press D and B at the same time.
• T
outside the allowab–10.0° C/14.0° F to 60.0°C/140.0 ° F) and the
calibration value sho‘‘ - -’’ .
• Setting a sensor calibration v
already stored in memory
4.A twice to e
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Calibration value
1.A until the
seconds star
screen.
2.C 10 times to display the temper
setting screen.
3.D to switch between Celsius (
) and F
( ).
• The initial factory default and the initial def
battery replacement is Celsius (
).
4.A twice to e
• The temperature displa
that are already stored in memory
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Temperature unit
Button Operation
The button operation tone sounds any time y
of the watch’s buttons
tone on or off as desired.
• Even if you turn off the button oper
Hourly
all operate normally
T
In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on (mute indicator not display
displayed).
• Since the C button is also the mode change b
button operation tone on or off also causes the w’ s current mode to change.
• The mute indicator is display
turned off.
Mute indicator
Auto Return Feature
• If you leav
operation f
to that point and exits the setting screen automatically
• The watch will change to the
any operation in the Fishing Mode
Hand Setting Mode for tw
Scrolling
The B and D buttons are used in v
through data on the display
operation scrolls through the data at high speed.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased b
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display f
range of noon to 11:59 pA (AM) indicator appears for times in the range
of midnight to 11:59 a.m.
• With the 24-hour format, times are display
any indicator
• The year can be set in the range of 2000 to 2099.
• The watch ’s built-in full automatic calendar makes allow
lengths and leap years
it e’s batteries replaced.
W
• The seconds count of the
Timekeeping Mode.
• All
Mode using UTC time differential v
