Operation Guide 4757
2
About Auto Receive
The watch receives the time calibr
When any auto receiv
performed.
selected Home
selected for y
Note
•
Auto receiv+0, +1 , or +2 is selected as the Home
Y
Auto Receive Start
1234 5 6
Standard Time
1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight
+ 0
Daylight Saving
2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am
Time
next da
Standard Time
2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am
next da
+ 1
Daylight Saving
3:00 am 4:00 am 5:00 am Midnight 1:00 am 2:00 am
Time
next da next da
Standard Time
3:00 am 4:00 am 5:00 am
Midnight
1:00 am 2:00 am
+ 2
next da next da
Daylight Saving
4:00 am 5:00 am
Midnight
1:00 am 2:00 am 3:00 am
Time
next da next day ne
Note
• Auto receiv
not performed if an auto receive time is reached while an alarm is sounding, or if a
setting screen (a screen with a flashing setting) is on the displa
• Auto receiv
morning, while you sleep (provided that the
Before going to bed f
location where it can receive the signal easily
• When auto receive is turned on, the watch receives the calibr
14 minutes e
calibration times.
after any one of the calibration times
• Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode.
shows any one of the calibr
time actually is the correct time.
Weak
Strong
(Level 0)
(Level 3)
Receiving indicator
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being receiv
best reception, be sure to keep the watch in a location where signal strength is
strongest.
operation is in progress.
• Use the receiving indicator as a guide for chec
best location for the watch during signal reception.
T
1. Enter the Receive Result Mode
2. Place the watch on a stab
o’ clock side) is f
3. Hold down B f
R0 starts to
flash on the displa
• The second hand will move to 12 o ’cloc
while actual reception is in progress
• The hour and minute hands stop while signal reception
is in progress.
• Time calibration signal reception takes from tw
minutes.
operations or mov
• After successful calibration signal reception is complete,
the hands will start moving to the correct setting.
they are moving, the current time will be sho
digital display
the digital display will s
reception was successful.
The watch will enter the
C or if you do not perf
or two minutes
• When receive is unsuccessful, the displa“
xx”.
The watch will enter the
changing the time setting if you press C or if y
perform any button oper
minutes.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Receiving
Receive successful
Receive failed
Note
• T
button.
Viewing the Latest Signal Reception Results
Y
correctly
T
Enter the Receive Result Mode.
• When receive is successful, the displa
that receive was successful.
successful, the display shows “
xx”.
• TC.
• If you adjust the time or date setting manually
display sho“
xx”.
Signal Reception
Check the f
• The watch is not in the Receive
Result Mode.
• Y
setting is not one of the following:
+0, +1 or +2 .
• Y
manually
• Y
settings when the auto receive start
times were reached.
• Y
receive was in progress
Cannot
perform
manual
receive
Auto receiv
is not being
performed
successfully
(“
xx”
displa
• Enter the Receive Result
Mode and try again.
• Select +0 , +1 or +2 as your
Home Time
• P
receive or wait until the ne
auto signal receive operation
is performed.
• Check to mak
watch is in a location where it
can receive the signal.
What you should doProb Probable Cause
Time setting
is incorrect
follo
signal
reception.
• The Home Time Zone setting is not
correct for the area where y
using the watch.
• The home position of the hands is
off.
• Select the correct Home
Time Zone.
• Enter the Home P
Adjustment Mode and adjust
the home position.
• For fur “Important! ” under “Time Calibration Signal Reception ”
and “Radio-controlled Atomic ”.
Alarm
When the alarm is tur
can also turn on an Hour
ev
• All of the operations in this section are perf
enter by pressing C.
Hourly time signal
on indicator
Alarm on
indicator
Alarm time
(Hour)
Alarm time
(Minutes)
T
1. In the Alarm Mode, hold down B until the hour setting of the alarm time star
flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
2. Press C to move the flashing between the hour and min
3. While a setting is flashing, use A (+) to change it.
• T
indicator) or p.m. indicator).
4. Press B to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• T
T
1.B until the hour setting of the alarm time starts to
flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
2.C to sound the alarm.
3.B to exit the setting screen.
Alarm On Indicator / Hourly
T
In the Alarm Mode, press B to cycle through the settings shown below
• The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
Signal Off
Alarm Off
Signal Off
Alarm On
Signal On
Alarm Off
Signal On
Alarm On
Adjusting the Home P
If the time and date settings are wrong ev
received normally
T
1. In the C three times to enter
the Home Position Adjustment Mode
2. Hold down B for about fiv
• The analog hands do not keep time dur
position adjustment.
3.A to align all of the analog hands with 12 o’ clock
(home position).
• Each press of A advances the second hand by one
second.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
12 o’ clock
Correct analog hand
home position
• Holding down A for more than two seconds causes the second hand to mov
continually at high speed.A again to stop high-speed hand movement at a
point that is just before 12 o’ cloc
pressing A as many times as necessary to align the hands with 12 o’ clock.
• High-speed hand movement will stop automatically if the hands complete a 12-
hour cycle.
4. Pressing B exits the home position adjustment.
