Bedienungsanleitung Casio 4777 (Seite 1 von 5) (Englisch)

466627

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Operation Guide 4777

MO0905-EB

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

••

• This watch does not have a city code that corresponds to the Greenwich

Mean Time differential of –3.5 hours. Because of this, the radio-controlled

atomic timekeeping function will not display the correct time for

Newfoundland, Canada.

Bright light

Solar cell

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run

down. Make sure the watch is exposed to light as much as

possible.

• When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

• You should try to keep the watch outside of your sleeve

as much as possible. Even if the face of the watch is

blocked only partially from light, charging will be reduced

significantly.

• The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will cause some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch

settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

Bright light

Electrical

energy

All

functions

enabled.

LEVEL 1

LEVEL 2

LEVEL 3

Charge

Solar cell

(Converts light to

electrical power.)

Rechargeable battery

LEVEL 1

LEVEL 2

LEVEL 3

All

functions

disabled.

All functions disabled,

except for analog timekeeping

and stopwatch.

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

• The actual level at which some functions are disabled depends on the watch model.

• Be sure to read “Power Supply” for important information you need to know

when exposing the watch to bright light.

If the analog hands aren’t moving...

If the analog hands aren’t moving, it means that the power saving mode has stopped

them to save battery power.

• See “Power Saving” for more information.

• The hands also stop whenever the battery level reaches Level 3.

About This Manual

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need in order to perform operations in

each mode. Further details and technical information

can be found in the “Reference” section.

Hour hand

Minute hand

Date

Second hand

Stopwatch second hand

24-hour hand

Day of the

week hand

Stopwatch Mode

Timekeeping Mode

World Time Mode

Press

B or D.

Press D.

(When the stopwatch

is reset to all zeros.)

Press C.

General Guide

Manual Receive Receive Status Check

Transmitter Change

Timekeeping Mode

▲

Press any button.

Hold down A

for about two seconds.

▲

Press A.

Hold down A

for about five seconds.

Press A.

Time/Date Adjustment

▲

Alarm Mode

▲

Press C.

▲

Press C.

▲

• About 1.5 seconds after you enter the World Time Mode or Alarm Mode from

another mode, the watch’s hands will start to move to the time setting for the mode

you entered. All button operations are disabled while the hands are moving. If you

need to pass through the World Time Mode or the Alarm Mode to get to another

mode, press C (mode change) to advance to the next mode before the hands start

moving.

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

• Supported time calibration signals: Germany (Mainflingen), England (Anthorn),

United States (Fort Collins), Japan (Fukushima or Fukuoka/Saga).

• See the information under “Signal Reception Troubleshooting” if you experience

problems with time calibration signal reception.

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time calibration

signal. You also can perform a manual procedure to set the time and date, when

necessary.

• The first thing you should do after purchasing this watch is to specify your

Home City, which is the city where you will normally use the watch. For more

information, see “To specify your Home City”.

• When using the watch outside the areas covered by the time calibration signal

transmitters, you will have to adjust the current time setting manually as required.

See “Timekeeping” for more information about manual time settings.

• The U.S. time calibration signal can be picked up by the watch while in North

America. The term “North America” in this manual refers to the area that consists of

Canada, the continental United States, and Mexico.

To specify your Home City

1. In the Timekeeping Mode, hold down A for about five

seconds. The watch will beep once after about two

seconds, and then twice after about three more seconds.

• This indicates the watch is in the setting mode.

•

Entering the setting mode will cause the stopwatch

second hand to move to the city code of the currently

selected Home City.

2. Use D to change the Home City setting.

• Each press of D causes the stopwatch second hand

to advance clockwise to the next city code.

• All hands (except for the second hand) and the date

display will change automatically to the applicable

settings for the currently selected city code. All button

operations are disabled while the hands and date

display are changing.

• Time calibration signal reception is supported when

any one of the city codes shown in the table below is

selected as your Home City.

City code

Stopwatch

second hand

• In addition to the above, you also can select city codes that are outside the ranges

of the time calibration signal transmitters supported by this watch.

• Note that this watch does not have a city code that corresponds to Newfoundland.

3. After the Home City setting is the way you want, press A to return to the

Timekeeping Mode.

• Normally, your watch should show the correct time as soon as you specify your Home

City code. If it does not, it should adjust automatically after the next auto receive

operation. You also can perform manual receive or you can set the time manually.

German/U.K. Signal Japan Signal U.S. Signal

City

Code

LON

PAR

ATH

City Name

London

Paris

Athens

City

Code

HNL

ANC

LAX

City Name

Honolulu

Anchorage

Los Angeles

City

Code

DEN

CHI

NYC

City Name

Denver

Chicago

New York

City

Code

HKG

TYO

City Name

Hong Kong

Tokyo

• Even if the time calibration signal is received correctly, there are some times when

the analog hands may not indicate the correct time. If this happens, use the

procedures under “Adjusting the Home Positions” to check the home positions of the

hands, and make adjustments as required.

• You can also change the Home City setting by swapping the current Home City and

the currently selected World Time City. For details, see “Swapping your Home City

and World Time City”.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

The time calibration signals transmitted from Mainflingen (Germany), Anthorn

(England), or Fort Collins (the United States) include both Standard Time and DST

data. When the Auto DST setting is turned on, the watch switches between Standard

Time and DST (summer time) automatically in accordance with the signals.

• Though the time calibration signal transmitted by the Fukushima and Fukuoka/Saga,

Japan transmitters include summer time data, summer time currently is not

implemented in Japan (as of 2007).

• The default DST setting is Auto DST (AUTO/AT) whenever you select LON, PAR ,

ATH , ANC, LAX, DEN, CHI, NYC, or TYO as your Home City code.

• If you experience problems receiving the time calibration signal in your area, it

probably is best to switch between Standard Time and Daylight Saving Time (summer

time) manually. For more information, see “To set the time and date manually”.

Casio 4777 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 4777

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info