Bedienungsanleitung Casio 5229 (Seite 3 von 6) (Englisch)

488899

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Operation Guide 5229

E-20

Lap Time

Lap time readings appear in the left digital dial. They show

the time elapsed since the last lap time reading was

taken.

• If you want the watch to calculate the speed of each lap

(when all of the laps are the same distance), specify the

lap distance for the distance setting (page E-15).

• If you want the watch to calculate the speed of the entire

race, specify the race distance for the distance setting

(page E-15). A speed will be indicated each time you

take a lap reading, but these lap speeds will not indicate

actual speed of the entire race.

To set up the stopwatch to take lap time readings

1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.

• If you need to reset the stopwatch to all zeros, press A.

2. Make sure that

LAP

(lap times) is shown in the left digital dial.

• If

SPL

(split times) is displayed, press A to toggle it to

LAP

Lap time

E-21

To perform a lap time measurement

Select lap time (

LAP

) measurement and then perform the

following button operations.

D Start ➝ A Lap* ➝ A Lap* ➝ D Stop ➝ A Reset

* Lap time remains frozen in the left digital dial for about

12 seconds. After that, elapsed time measurement

reappears.

• You can press A to take lap readings as many times as

you like.

• While a lap time is displayed, the right digital dial will

alternate between the lap number (#01 to #99) and the

lap hour value. If you take more than 99 lap readings,

the lap number will restart from #00 following lap #99.

• Pressing D to stop elapsed time measurement displays

the time (and speed if a distance is specified) of the final

lap.

Lap number

Speed hand

(calculated)

Minutes

Seconds

1/1000 seconds

Hours

E-22

Split Time

Split time readings appear in the left digital dial. They

show the time elapsed since the beginning of the current

time measurement.

• If you want the watch to calculate the speed of the race,

specify the race distance for the distance setting (page

E-15).

• For split time readings, you can specify the total race

distance only. Though the watch will indicate a speed

each time you take a split reading, they will be based on

the total race distance, and so they will not indicate

actual intermediate split speeds.

To set up the stopwatch to take split time readings

1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.

• If you need to reset the stopwatch to all zeros, press A.

2. Make sure that

SPL

(split times) is shown in the left digital dial.

• If

LAP

(lap times) is displayed, press A to toggle it to

SPL

Split time

E-23

To perform a split time measurement

Select split time (

SPL

) measurement and then perform

the following button operations.

D Start ➝ A Split ➝ A Split Release* ➝ D Stop ➝

A Reset

* The split time is released automatically if you do not

press A within about 12 seconds.

• You can press A to take split readings as many times

as you like.

• The stopwatch continues elapsed time measurement

internally while a split time reading is displayed.

• Pressing A while a split time is displayed will switch

back to normal elapsed time measurement. The elapsed

time will appear in the left digital dial.

• You also could press D to stop elapsed time

measurement instead.

• Pressing D to stop elapsed time measurement displays

the time (and speed if a distance is specified) of the final

split (which is the overall elapsed time).

Hours

Speed hand

(calculated)

Minutes

Seconds

1/1000 seconds

E-24

To measure times with the stopwatch

Elapsed Time

Lap Time

Split Time

Start

Stop Reset

➤➤

Start

(

SPL

displayed)

Split Split release Stop

➤➤➤

Reset

➤

Start

(

LAP

displayed)

Lap

(Lap01)

Stop Reset

➤➤ ➤

➤

Lap

(Lap02)

E-25

Countdown Timer

You can set the countdown start time within a range of

one minute to 24 hours. An alarm sounds when the

countdown reaches zero.

• You also can select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

C (page E-7).

Seconds

Auto-repeat off

Start time

(Hours : Minutes)

E-26

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown in the left digital

dial.

• When the end of the countdown is reached, the alarm will sound for 10 seconds or

until you stop it by pressing any button.

• If auto-repeat is turned off, the countdown time is reset to its starting value

automatically after the alarm stops.

• If auto-repeat is turned on, the countdown will restart automatically without pausing

when it reaches zero.

• The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

• Press D while a countdown operation is in progress to pause it.

Press D again to resume the countdown.

• To stop a countdown timer operation completely, first pause it (by pressing D), and

then press A. This returns the countdown time to its starting value.

E-27

To configure countdown start time and auto-repeat settings

1. While the countdown start time is shown in the left

digital dial in the Countdown Timer Mode, hold down A

for about three seconds until the hour setting of the

countdown start time starts to flash. This is the setting

mode.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” (page

E-26) to display it.

2. Press C to move the flashing in the sequence shown

below, and select the setting you want to change.

Start Time

(Minutes)

Auto-Repeat

On/Off

Start Time

(Hours)

3. Perform the following operations, depending on which setting is currently selected

in the left digital dial.

• While the start time setting is flashing, use D (+) and B (–) to change it.

• To toggle auto repeat between on and off, press D while the on/off setting is

flashing in the left digital dial.

Start time

(Hours : Minutes)

Auto-repeat on

E-28

4. Press A to exit the setting mode.

• The auto-repeat on (

) indicator is displayed on the Countdown Timer Mode

screen while this function is turned on.

E-29

World Time

World Time digitally displays the current time in one of

48 cities (29 time zones) around the world. A simple

operation swaps your Home City with the currently

selected World Time City.

• The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

• Times in the World Time Mode are based on UTC

offsets. See the “City Code Table” at the back of this

manual for information about the UTC offsets that are

supported.

• All of the operations in this section are performed in the World Time Mode, which

you enter by pressing C (page E-7).

Currently selected

World Time City

World Time

Casio 5229 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5229

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info