Bedienungsanleitung Casio 5288 - BGA-160 (Seite 4 von 5) (Englisch)

624958

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Operation Guide 5288

E-39

To change the illumination duration

In the Timekeeping Mode, hold down 1. A until the seconds start to ﬂ ash. This is

the setting mode.

Press 2. C nine times so the illumination duration setting mode is on the display.

Press 3. D to toggle the illumination duration between 1.5 seconds (

) and

3 seconds (

After the settings are the way you want, press 4. A to exit the setting mode.

Illumination Precautions

Illumination may be hard to see when viewed under direct sunlight.

•

Illumination turns off automatically whenever an alarm sounds. •

Frequent use of illumination runs down the battery. •

E-38

Illumination

The face of the watch is illuminated for easy reading in

the dark.

To turn on illumination

In any mode (except when a setting mode, with ﬂ ashing

digits is on the display), press B to illuminate the display.

You can use the procedure below to select either x

1.5 seconds or 3 seconds as the illumination duration.

When you press B, the display will remain illuminated

for about 1.5 seconds or 3 seconds, depending on the

current illumination duration setting.

E-37

If you need to advance the analog time setting a long way, hold down x D until

the time starts advancing at high speed, and then press B. This locks the high-

speed hand movement, so you can release the two buttons. High-speed hand

movement continues until you press any button. It will also stop automatically

after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,

or countdown beeper) starts to sound.

Press 4. A to exit the setting mode.

The watch will automatically adjust the minute hand slightly to match its internal

second count when you exit the setting mode.

To return to the Timekeeping Mode, press x C.

E-36

Adjusting the Analog Hand Setting

Use the following procedure to adjust the analog hands so their settings match the

digital time.

To adjust the analog time

Use 1. C to select the Hand Setting Mode as shown on

page E-11.

Hold down 2. A until the current digital time starts to

ﬂ ash, which indicates the analog setting mode.

Press 3. D to advance the analog time setting by

20 seconds.

Holding down x D advances the analog time setting

at high speed.

E-35

Press 5. A to exit the setting mode.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn an alarm and the Hourly Time Signal on and off

In the Alarm Mode, use 1. D to select an alarm or the

Hourly Time Signal.

When the alarm or the Hourly Time Signal you want is 2.

selected, press A to toggle it between on and off.

The alarm on indicator (when any alarm is on), snooze x

alarm indicator (when the snooze alarm is on), and the

Hourly Time Signal on indicator (when the Hourly Time

Signal is on) are shown on the display in all modes.

To stop the alarm

Press any button.

Hourly time signal

on indicator

Snooze alarm indicator

E-34

To set an alarm time

In the Alarm Mode, use 1. D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

AL1 AL3 SNZAL2 AL4 SIG

DDDDD

Hold down 2. A for about two seconds until the alarm time starts to ﬂ ash. This is

the setting mode.

Press 3. C to move the ﬂ ashing between the hour and minute settings.

While a setting is ﬂ ashing, use 4. D (+) and B (–) to change it.

When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. (P indicator).

Alarm ON/OFF indicator

E-33

To enter the Alarm Mode

Use C to select the Alarm Mode as shown on page E-11.

The snooze alarm screen is indicated by

x SNZ, while the other alarm screens are

numbered AL1 through AL4. The Hourly Time Signal screen is indicated by SIG.

When you enter the Alarm Mode, the data you were viewing when you last exited

the mode appears ﬁ rst.

E-32

Using the Alarm

You can set ﬁ ve independent daily alarms. When a

daily alarm is turned on, an alarm tone will sound

for about 20 seconds each day when the time in the

Timekeeping Mode reaches the preset alarm time.

This is true even if the watch is not in the Timekeeping

Mode. One of the alarms is a snooze alarm, while the

other four are one-time alarms. The snooze alarm

operation repeats every ﬁ ve minutes.

You can also turn on an Hourly Time Signal, which will

cause the watch to beep twice every hour on the hour.

Alarm number

Alarm time (Hour : Minutes)

E-31

Note

The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59 seconds.

Once started, stopwatch timing continues until you press x D to stop it, even if

you exit the Stopwatch Mode to another mode and even if timing reaches the

stopwatch limit deﬁ ned above.

Exiting the Stopwatch Mode while a split time is frozen on the display clears the

split time and returns to elapsed time measurement.

E-30

To perform an elapsed time operation

D D D A

Start Stop (Restart) (Stop) Reset

To pause at a split time

A A D A

Start Split

(SPL displayed)

Split release Stop Reset

To measure two ﬁ nishes

A D A A

Start Split

(SPL displayed)

First runner ﬁ nishes.

Display time of ﬁ rst

runner.

Stop

Second runner

ﬁ nishes.

Split release

Display time of

second runner.

Reset

Casio 5288 - BGA-160 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5288 - BGA-160

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info