Bedienungsanleitung Casio 5311 - GW-A1100 (Seite 1 von 11) (Englisch)

624480

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Operation Guide 5311

E-9

2. Check the Home City.

Use the procedure under “To conﬁ gure Home City settings” (page E-36) to conﬁ gure your

Home City.

Important!

x Proper time calibration signal reception depends on correct Home City, time, and

day settings in the Timekeeping Mode. Make sure you conﬁ gure these settings

correctly.

3. Set the current time.

x To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-25).

x To set the time manually

See “Conﬁ guring Current Time and Day Settings Manually” (page E-41).

The watch is now ready for use.

x For details about the watch’s radio controlled timekeeping feature, see “Radio

Controlled Atomic Timekeeping” (page E-20).

E-8

Things to check before using the watch

1. Hold down C at least two seconds to enter the Timekeeping Mode, and

then observe the movement of the

Second Hand.

Is the

Second Hand moving smoothly at one-second intervals?

Is the

Second Hand moving at

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged. For details

about charging, see “Charging the

Watch” (page E-14).

Power is low. Charge the watch by

placing it in a location where it is

exposed to light. For details, see

“Charging the Watch” (page E-14).

YES

E-7

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the

current high-speed movement or press any button.

Note

x If you do not perform any operation for more than two minutes after pulling out the

crown, crown operations will become disabled automatically. If this happens, push

the crown back in and then pull it out again to re-enable crown operations.

x You can use high-speed hand movement when conﬁ guring time settings in the

Timekeeping Mode, Alarm Mode, or Countdown Timer Mode.

x Button operations become disabled after you perform a crown operation. If this

happens, rotate the crown slightly. This should restore button operations.

E-6

High-speed Movement

When rotating the crown to move the hands of the watch, you can use the operations

described below to move the hands at high speed, either forward or back. There are

two high-speed levels: HS1 and HS2 (faster than HS1).

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly three turns away

from you (for forward movement) or towards you (for reverse

movement). High-speed movement will continue even if you

release the crown.

To start HS2 high-speed movement

While HS1 high-speed movement is in progress, again rotate

the crown rapidly three turns in the same direction as the

current HS1 movement (away from you for forward movement

or towards you for reverse movement).

E-5

4. Gently pull on the crown to make sure it is securely locked and does not come out.

To unlock the crown

Rotate the crown so the groove aligns with Mark 1.

To pull out, rotate, or push the crown in

Important!

x Before performing any of these operations, ﬁ rst unlock the crown.

The illustrations below show the different crown operations.

Pull out Rotate Push in

E-4

Using the Crown

This watch has a lock-type crown.

Important!

x You should normally have the crown locked during normal daily use. Leaving the crown

unlocked creates the risk of unintended operations or even damage due to impact.

To lock the crown

1. Push the crown back in (see “To pull out, rotate, or push the

crown in” below).

x Note that attempting to lock the crown when it is not pushed

in can cause unexpected watch operation.

2. Rotate the crown so any one of its three grooves is aligned

with Mark 1.

3. While pushing in on the crown (a), rotate it to the right (b) until

it stops, and align the groove with Mark 2.

Mark 1

Groove

Mark 2

E-3

About This Manual

Operations are performed using the watch’s crown, and

the three buttons indicated by the letters A, B and C in

this manual.

Hands and Indicators

Hour Hand

Second Hand

Minute Hand

Upper Dial Hand: Indicates a time, in 24-hour format,

depending on the current mode.

Lower Dial Hand: Indicates the current mode.

Day Indicator

This User’s Guide uses numbers shown above to identify

watch hands and indicator.



>B @

E-2

Warning!

x The measurement functions built into this watch are not intended for taking

measurements that require professional or industrial precision. Values produced

by this watch should be considered as reasonable representations only.

x To ensure correct direction readings by this watch, be sure to perform

bidirectional calibration before using it. The watch may produce incorrect

direction readings if you do not perform bidirectional calibration. For more

information, see “To perform bidirectional calibration” (page E-56).

x Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

x Note that the product illustrations in this manual are intended for reference only, and

so the actual product may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours. Because of this, the radio-controlled atomic timekeeping function will not

display the correct time for Newfoundland, Canada.

MA1303-EA

#!3)/#/-054%2#/,4$

Casio 5311 - GW-A1100 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5311 - GW-A1100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info