Bedienungsanleitung Casio 5425 (Seite 3 von 6) (Englisch)

586703

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Operation Guide 5146 5425

E-20

Lap Time

A lap time reading shows the time elapsed since the last

lap time reading was taken.

•



If you want the watch to calculate the speed of each lap

(when all of the laps are the same distance), specify the

lap distance for the distance setting (page E-15).

•



If you want the watch to calculate the speed of the

entire race, specify the race distance for the distance

setting (page E-15). A speed will be indicated each

time you take a lap reading, but these lap speeds will

not indicate actual speed of the entire race.

To set up the stopwatch to take lap time readings

1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.

• If you need to reset the stopwatch to all zeros, press $.

2. Make sure that LAP (lap times) is shown in the lower digital display.

• If SPL (split times) is displayed, press

to toggle it to LAP.

Lap time

E-21

To perform a lap time measurement

Select lap time (LAP) measurement and then perform the

following button operations.

Start

➝ $

Lap*

➝ $

Lap*

➝

Stop

➝ $

Reset

* Normal elapsed time measurement reappears after

about 12 seconds.

• You can press

to take lap readings as many times

as you like.

• While a lap time is displayed, the upper digital display

will alternate between the lap number (

#01

#99

) and

the lap hour value. If you take more than 99 lap

readings, the lap number will restart from

#00

following

lap

#99

• Pressing

to stop elapsed time measurement

displays the time (and speed if a distance is speciﬁ ed)

of the ﬁ nal lap.

Lap number

Speed hand

(calculated)

Minutes

Seconds

1/1000

second

Hours

E-22

Split Time

A split time reading shows the time elapsed since the

beginning of the current time measurement.

• If you want the watch to calculate the speed of the race,

specify the race distance for the distance setting (page

E-15).

• For split time readings, you can specify the total race

distance only. Though the watch will indicate a speed

each time you take a split reading, they will be based

on the total race distance, and so they will not indicate

actual intermediate split speeds.

To set up the stopwatch to take split time readings

1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.

• If you need to reset the stopwatch to all zeros, press $.

2. Make sure that SPL (split times) is shown in the lower digital display.

• If LAP (lap times) is displayed, press

to toggle it to SPL.

Split time

E-23

To perform a split time measurement

Select split time (SPL) measurement and then perform the

following button operations.

Start

➝ $

Split

➝ $

Split Release*

➝

Stop

➝ $

Reset

* The split time is released automatically if you do not

press

within about 12 seconds.

• You can press

to take split readings as many times

as you like.

• The stopwatch continues elapsed time measurement

internally while a split time reading is displayed.

• Pressing

while a split time is displayed will switch

back to normal elapsed time measurement. The

elapsed time will appear in the lower digital display.

• You also could press

to stop elapsed time

measurement instead.

• Pressing

to stop elapsed time measurement

displays the time (and speed if a distance is speciﬁ ed)

of the ﬁ nal split (which is the overall elapsed time).

Hours

1/1000

second

Minutes

Seconds

Speed hand (calculated)

E-24

To measure times with the stopwatch

Elapsed Time

D A

Start Stop Reset

Lap Time

A A D A

Start

(

LAP

displayed)

Lap

(Lap01)

Lap

(Lap02)

Stop Reset

Split Time

A A D A

Start

(

SPL

displayed)

Split Split release Stop Reset

E-25

Countdown Timer

You can set the countdown start time within a range of

one minute to 24 hours. An alarm sounds when the

countdown reaches zero.

• You also can select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

(page E-7).

Second

Auto-repeat off

Start time

(Hours : Minutes)

E-26

To use the countdown timer

Press

while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached, the alarm will sound for 10 seconds or

until you stop it by pressing any button.

• The countdown time is reset to its starting value automatically after the alarm stops

if auto-repeat is turned off.

• When auto-repeat is turned on, the countdown will restart automatically without

pausing when it reaches zero.

• The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

• Press

while a countdown operation is in progress to pause it.

• Press

again to resume the countdown.

• To stop a countdown timer operation completely, ﬁ rst pause it (by pressing

and then press

. This returns the countdown time to its starting value.

E-27

To conﬁ gure countdown start time and auto-repeat settings

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down

for about three

seconds until the hour setting of the countdown start

time starts to ﬂ ash. This is the setting mode.

• If the countdown start time is not displayed, use

the procedure under “To use the countdown timer”

(page E-26) to display it.

2. Press

to move the ﬂ ashing in the sequence shown

below, and select the setting you want to change.

Start Time

(Minutes)

Auto-Repeat

On/Off

Start Time

(Hours)

3. Perform the following operations, depending on which setting currently is selected

on the display.

• While the start time setting is ﬂ ashing, use ' (+) and % (–) to change it.

• While the auto-repeat on/off setting is ﬂ ashing on the display, press ' to

toggle auto-repeat on (

) and off ( ).

Start time

(Hours : Minutes)

Auto-repeat on

E-28

4. Press

to exit the setting mode.

• The auto-repeat on ( ) is displayed on the Countdown Timer Mode screen while

this function is turned on.

E-29

World Time

World Time digitally displays the current time in one of

48 cities (29 time zones) around the world. A simple

operation swaps your Home City with the currently

selected World Time City.

• The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

• Times in the World Time Mode are based on UTC

offsets. See the “City Code Table” at the back of this

manual for information about the UTC offsets that are

supported.

• All of the operations in this section are performed in the World Time Mode, which

you enter by pressing

(page E-7).

Currently selected

World Time City

World Time

Casio 5425 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5425

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info