Bedienungsanleitung Casio 5470 - PRX-8000 (Seite 12 von 26) (Englisch)

624835

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Note

●

The second hand will point to r

(over) if the current altitude

differential

is greater than the setting

value, or s (under) if it is lower than

the setting value.

If either of these is indicated while

using the ±100 m (328 feet)

measurement range, change the

range setting to ±1000 m (3280

feet).

●

The second hand will move to 9

o’clock if a reading is outside the

allowable altitude measurement

range

(-700 m to 10,000 m (-2,300 to

32,800 feet)), or if a reading error

occurs.

Setting the Auto

Measurement Interval

You can select an auto measurement interval

of either five seconds or two minutes.

Pull out the crown.

Press (B).

Crown

Rotate the crown to select [0’05] or [2’00]

as the auto measurement interval.

[0’05]: Readings taken every second for

the

first three minutes, and then every five

seconds for about the next one hour.

[2’00]: Readings taken every second for

the

first three minutes, and then every two

minutes for about the next 12 hours.

Push the crown back in to complete the

setting operation.

Note

●

The watch will automatically return

to the Timekeeping Mode if you do

not perform any operation in the

Altimeter Mode for about one hour

while [0’05] is selected as the

measurement interval or about 12

hours while [2’00] is selected.

Recording Altitude Readings

Use the procedure below to record altitude

measurements manually. Auto

measurements are also recorded

automatically.

●

Use the Altitude Record Recall Mode to

view or delete records.

Viewing Altitude Records

●

Recording Altitude Data Manually

Hold down the (A) button for about two

seconds, until [REC] stops flashing on the

display. This records the current altitude

reading, along with the recording date and

time.

●

There is enough memory to hold up to 30

altitude records.

●

Recording altitude data when there are

already

30 records in memory automatically

deletes the oldest record to make room for

the new one.

●

Auto Altitude Data Recording

The altitude data described below is recorded

automatically while the watch is in the Altitude

Mode. One record each is maintained in

memory for each of these items.

End point

Start point

High Altitude (MAX): E

Low Altitude (MIN): F

Cumulative Ascent (ASC): A+C

Cumulative Descent (DSC): B+D

* Cumulative ascent and cumulative descent

values are updated whenever there is a

difference of at least ±15 m (±49 feet) from

one reading to the next.

Note

●

Auto recording ends when you exit

the

Altimeter Mode. Re-entering the

Altimeter Mode restarts recording of

cumulative values from where it was

stopped when you last exited the

Altimeter Mode.

Specifying the Altitude

Measurement Unit

You can select either meters (m) or feet (ft) as

the Altitude Mode display unit.

Important!

●

When Tokyo (TYO) is set as the

Home City, the altitude unit is fixed

as meters (m) and cannot be

changed.

Pull out the crown.

Press (B) three times.

Crown

Rotate the crown to select meters (m) or

feet (ft) as the measurement unit.

Push the crown back in to complete the

setting operation.

Operation Guide 5470

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio 5470 - PRX-8000 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5470 - PRX-8000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info