Bedienungsanleitung Casio AT-3 (Seite 156 von 163) (Englisch)

586715

156

Zoom out

Zoom in

Vorherige Seite

1/163

Nächste Seite

Reference

E-154

14: Lo-Fi

Applies various types of noise to the input signal to reproduce

a retro Lo-Fi sound.

Includes wow and flutter for rotational fluctuation like that in

tapes and records, a Noise 1 generator that generates

continual FM radio type, and a Noise 2 generator that

generates record play types scratch noise.

Parameters and Value Ranges:

1 :Wow and Flutter Rate

(0 to 127)

Adjusts the wow and flutter rate.

2 :Wow and Flutter Depth

(0 to 127)

Adjusts the wow and flutter depth.

3 :Noise1 Level (0, 1, 2, 3, 4, 5)

Adjusts the level of Noise Generator 1.

4 :Noise2 Level (0, 1, 2, 3, 4, 5)

Adjusts the level of Noise Generator 2.

5 :Noise2 Density (0, 1, 2, 3, 4, 5)

Adjusts the frequency of Noise Generator 2.

6 :Bit (0, 1, 2, 3)

Distorts the sound. A larger number produces greater

distortion.

Important!

Raising the noise level while a note is not sounding will cause

noise to sound, even if there is no input signal.

■ Dual Type DSP Parameters

Dual type DSPs are configured by combining two different

single type DSPs. Use the procedure below to determine what

parameters that can be configured for each dual type DSP,

and the operation, and setting ranges of dual type DSPs.

Example: Type number 29: Distortion-Wah

1. The DSP type name has two parts: a left side part and a

right side part.

Distortion-Wah 3 “Distortion” and “Wah”

2. Find out what parameters you can configure by looking up

the left side part of a dual type DSP in the “Type Name”

column of the table below.

3. Find the same type names in the table under “Single Type

DSP Parameters” on pages E-152 through E-154, and note

the operation and setting ranges of the items that are the

same as those shown in the “Configurable Parameters”

column of the above table.

4. Next, repeat steps 2 and 3 above for the right side part of

the dual type DSP parameter name.

Type Name Configurable Parameters

Wah LFO Waveform

LFO Rate

LFO Depth

Distortion Gain

Level

Chorus LFO Waveform

LFO Rate

LFO Depth

Flanger LFO Waveform

LFO Rate

LFO Depth

Reflection Feedback

Compressor Threshold

Level

Auto Pan LFO Waveform

LFO Rate

LFO Depth

Tremolo LFO Waveform

LFO Rate

LFO Depth

• In our “Distortion-Wah” example, the left side part of the

name is “Distortion” so we can see in the above table

that “Gain” and “Level” parameters can be configured.

You can find out about the operations and setting ranges

of “Gain” and “Level” by referring to “03: Distortion” on

page E-152.

• The parameter numbers that appear on the parameter

setting screen start from 1, and the number is

incremented for each successive parameter.

The parameter numbers of our “Distortion-Wah” example

would be as shown below.

1: Gain

2: Level

3: LFO Waveform

4: LFO Rate

5: LFO Depth

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio AT-3 Seite 156

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio AT-3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info