Bedienungsanleitung Casio CT-X9000IN (Seite 10 von 147) (Englisch)

723292

Zoom out

Zoom in

Vorherige Seite

1/147

Nächste Seite

EN-9

Preparing a Power Supply

You can use six D-size batteries for power.

• Be sure to turn off power before loading batteries.

• It is up to you to prepare six commercially available

batteries. Do not use oxyride batteries or any other

nickel based batteries.

Open the battery cover on the bottom of the

Digital Keyboard.

Load six D-size batteries into the battery

compartment.

• Make sure the positive + and negative - ends of the

batteries are facing as shown in the illustration.

Insert the tabs of the battery cover into the

holes on the side of the battery compartment,

and close the cover.

■ Low Battery Indication

The indicators shown below start to flash to let you know

when battery power is low. Replace the batteries with new

ones.

Connect the Digital Keyboard to a power

supply.

• See “Using the AC Adaptor” (page EN-8) or

“CT-X8000IN: Using Batteries” (page EN-9).

Press 1P (power) to turn on power.

•Use 2 VOLUME to adjust volume.

To turn off power, hold down 1P (power)

again.

The message “Bye” will appear on the display and then

power will turn off.

• If you press 1P (power) only lightly, the display will

light up momentarily but power will not turn on. This

does not indicate malfunction. Press 1P (power)

firmly and completely to turn on power.

• Turning off the Digital Keyboard causes most current

settings to be cleared. While Auto Resume function

(page EN-10) is turned on, most settings are retained

even when power is turned off.

• Never try to perform any operation while the “Wait...”

or “Bye” message is displayed. The “Wait...” or “Bye”

message indicates that an internal data save operation

is being performed. Turning off the Digital Keyboard

can cause Digital Keyboard data to be deleted or

become corrupted.

• Pressing 1P (power) to turn off power actually puts the

Digital Keyboard into a standby state. Minute amounts of

current continue to flow within the Digital Keyboard in the

standby state. If you do not plan to use the Digital Keyboard

for a long time or if there is a lightning storm in your area,

be sure to unplug the AC adaptor from the power outlet.

If you do not perform any operation on the Digital Keyboard

for about 30 minutes, power will turn off automatically.

• You can disable Auto Power Off to ensure that power is not

turned off automatically during a concert, etc.

Perform the procedure under “To configure function

settings with the bk FUNCTION button” (page EN-107)

and disable the following setting: Other (Other) 3 Auto

Power Off (AutoOff) (page EN-112).

CT-X8000IN: Using Batteries

Tabs

Low battery indicators (flash)

Turning Power On or Off

Auto Power Off

CT-X9000_8000IN_EN.book 9 ページ２０１８年４月１２日　木曜日　午後１時８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio CT-X9000IN Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info