Bedienungsanleitung Casio DQD-105 (Seite 2 von 4) (Englisch)

723415

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Operation Guide DQD-105

TIME CALIBRATION SIGNAL RECEPTION PRECAUTIONS

• This clock is able to receive the time calibration signal transmitted from

Mainflingen, Germany (located 25 kilometers southeast of Frankfurt).

Signal reception is possible within approximately 1,500 km of the

transmitter.

• Even when the clock is within the reception range, signal reception is

impossible if the signal is blocked by mountains or other geological

formations between the clock and signal source.

• Signal reception is affected by weather, atmospheric conditions, and

seasonal changes.

• The time calibration signal is bounced off the ionosphere. Because of

this, such factors as changes in the reflectivity of the ionosphere, as

well as movement of the ionosphere to higher altitudes due to seasonal

atmospheric changes or the time of day may change the reception

range of the signal and make reception temporarily impossible.

• Reception is best when the back of the clock is facing toward

Mainflingen. Note, however, that moving the clock while the time

calibration signal receive operation is taking place will make stable

reception impossible.

• Think of the clock as acting like a TV or radio when it is receiving the calibration signal.When receiving indoors,

move to a location as near as possible to a window. Proper signal reception can be difficult or even impossible

under the conditions listed below.

Inside, among

buildings, or near

neon signs

Inside a vehicle Near refrigerators

or other household

appliances, near

office equipment,

mobile phones or

wireless LAN

devices.

Near a

construction site,

airport, or other

sources of

electrical noise,

underground or in

tunnels, near

railroads,

highways, or radio

stations with

interfering

frequencies.

Near high-tension

power lines

Among or behind

mountains

1,500 km

500 km

Mainflingen

• Signal reception is normally better at night than during the day.

• Radio interference can make signal reception impossible.

• Strong electrostatic charge can result in the wrong time being set.

• The alarm does not operate during signal reception.

USING THE CLOCK

Any of the following procedures can be used to set current date and time.

• Auto receive of the time calibration signal

• Manual receive of the time calibration signal

• Manual setting without using the time calibration signal

Auto Receive

• The clock receives the time calibration signal eight times each day (2:00, 5:00, 8:00, 11:00, 14:00, 17:00, 20:00,

23:00).

• A signal receive operation takes from two to ten minutes under good signal conditions.

Antenna Icon

Receive in progress: Icon flashes

Receive failed: Icon not displayed

Receive successful: Icon displayed

Wave OK Indicator

Receive in progress: OK not displayed

All receives over the past 24 hours failed: OK not displayed

At least one successful receive over the past 24 hours: OK displayed

Unsuccessful Signal Reception

The antenna icon disappears from the display when a signal receive operation is unsuccessful. If this happens,

try changing the position or orientation of the clock, and press the WAVE button (2) to receive again.

Manual Receive

• Press the WAVE button (2) to start a calibration signal receive operation.

• Use the WAVE button (2) to perform a receive operation after replacing the clock’s batteries or if the auto

receive operation was not performed correctly for some reason.

• The clock beeps and display illumination flashes for about three seconds when a receive operation triggered by

the WAVE button (2) is successful.

Important!

• Do not perform any button or switch operation while a signal receive operation is in progress.

• The time calibration signal includes both Standard Time and Daylight Saving Time (summer time) data.

• The DST indicator appears on the display when Daylight Saving Time (summer time) data is received.

Setting the Time and Date Manually

• When using the clock in an area that is outside of the range of the transmitter in Mainflingen or in an area where

signal reception is impossible for some reason, you need to adjust the time manually as required.

1. Press the SET button (5) to cycle through the setting screens as shown below.

2. While the screen you want is on the display, use the Alarm Time Set buttons (4) to change the digits that are

flashing.

Press

—

to decrease

the flashing digits.

Press + to increase

the flashing digits.

• Holding down + or – changes the flashing digits at high speed.

• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with

the date setting.

• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00.

• Each press of + or – while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour

and 24-hour timekeeping.

3. After making the settings you want, use the SET button (5) to display the Normal Timekeeping Screen.

• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for

about three minutes without performing any operation.

SET button (5)

SET button

(5)

Normal Timekeeping Screen

Year Setting Screen

12-hour/24-hour Timekeeping Screen

Month and Day Setting Screen Time Setting Screen

Casio DQD-105 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info