Bedienungsanleitung Casio DQD-110 (Seite 4 von 4) (Englisch)

723418

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Operation Guide DQD110/120B

USING THE ALARM 2

Stopping the Alarm

• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the

snooze feature is turned on, the alarm will sound again in about five minutes.

• To turn off the snooze feature, slide the Alarm Mode selector (4) to OFF.

Using the Hourly Time Signal

• When turned on, the Hourly Time Signal sounds on the every hour on the hour from

6:00 a.m. to midnight (19 times per day).

• Press the SIG button (5) to toggle the Hourly Time Signal on and off.

• The SIG indicator indicates that the Hourly Time Signal is turned on.

THERMOMETER FUNCTIONS

• A built-in sensor measures temperature and shows the measured value on the display.

• The displayed temperature is replaced by “LO” for temperatures –20.0°C (–4.0°F) and lower, and “HI” for

temperatures 50.0°C (122.0°F) and higher.

• Though temperature readings are displayed up to 0°C (32°F) and greater than 40.1°C (104.1°F), note that such

readings are actually outside the guaranteed temperature range of this clock.

Switching between Celsius and Fahrenheit

• See “Setting the Time and Date Manually” for information about selecting Celsius (°C) or Fahrenheit (°F) as the

temperature unit.

High Temperature and Low Temperature Memory

• The following data is stored in memory automatically.

Current Temperature

MAX/MIN button ( )

High Temperature

Low Temperature

• Holding down the MAX/MIN (2) button for about two seconds starts auto display, which cycles automatically

between the current, high, and low temperatures. To exit auto display, press the MAX/MIN button (2) again.

• High temperature and low temperature memory is cleared each day at midnight.

USING THE LIGHT

Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark.

Important!

• Overuse of the light can shorten battery life.

BATTERY REPLACEMENT

Replace batteries whenever the display of the clock becomes dim and difficult to read.

1. Pressing down lightly on the battery compartment cover, slide it downwards and remove it.

2. Remove both of the old batteries.

3. Load two new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If

you load batteries incorrectly, they can burst and damage the clock.

4. Press the RESET button (7). Be sure to press the RESET button (7) after replacing batteries.

5. Replace the battery compartment cover.

Battery precautions

•

Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician

immediately.

• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.

• Never mix old and new batteries, or batteries of different brands.

• Never charge the batteries that come with the clock.

•

Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your skin.

• Replace the batteries at least once a year, even if the current batteries are working properly.

• The batteries that come with the clock lose some of their power during transport and storage.

Hourly Time Signal On

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio DQD-110 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info