Bedienungsanleitung Casio EA200 (Seite 11 von 55) (Englisch)

14279

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

20020601

English

1-5

Using the Built-in Speaker

To output sound recorded by the built-in microphone

(1) Send Command 0 to initialize the EA-200 setup.

{0} → List 1

_ Stores {0} to List 1. 0 is the command number.

Send (List 1)

_ Sending List 1 executes Command 0.

(2) Send Command 1 to specify microphone as the channel.

{1, 10} → List 1

_ 1 is the command number, and 10 indicates use of

Send (List 1)

_ the built-in microphone.

(3) Send Command 3 to configure measurement condition settings.

{3, 0.00005, 120000} 3 is the command number, 0.00005 is the sampling interval

→ List 1

_ (50µs), and 120000 is the number of samples.

Send (List 1)

^ You can change sampling conditions by using different

sampling interval and number of samples values, if you want.

At this time, the Ready lamp lights on the EA-200.

Press the EA-200 [START/STOP] key to start sampling.

When sampling is complete, press the calculator’s w key to restart the program.

^ (Disp command) causes processing to stop until you press the w key.

(4) Send Command 0 to initialize the EA-200 setup.

{0} → List 1

_ Stores {0} to List 1. 0 is the command number.

Send (List 1)

_ Sending List 1 executes Command 0.

(5) After sampling is complete, use Command 1 to configure speaker settings.

{1,12, 5,10} → List 1

_ 1 is the command number, 12 specifies the speaker as the

Send (List 1)

_ channel, 5 is the number of loops, and 10 specifies output of

values sampled by the microphone.

(6) Re-configure the sampling condition settings.

{3,0.00005,120000} 3 is the command number, 0.00005 is the sampling interval

→ List 1

_ (50

µs), and 120000 is the number of samples.

Send (List 1)

^ You can change sampling conditions by using different

sampling interval and number of samples values, if you want.

(7) Press [START/STOP] to output the sound recorded with the microphone.

Status Request

This function can be used to fetch the current status of the EA-200.

To use Status Request

{7} → List 1

_ Sends Command 7.

Send (List 1)

Receive (List 1)

_ Receives the status information and stores it in List 1.

Line 1 Line 2 Line 3 Line 4

Status Error Code Battery Condition OS Version

0: Standby = O: Normal 0 to 999 Version No.

(

No Sample Data in EA-200

) ≠ O: Error

1: Ready Integer: Command number < 450:

2: Sampling Decimal Part: Parameter position low battery

3: Standby

(

Sample Data in EA-200

) Example: 3.2

Second parameter of Command 3.

Sampling interval value error

Auto Setup

Auto Setup detects the Auto-ID of a probe, and configures applicable settings automatically.

The three probes (voltage, temperature, optical) that come bundled with the EA-200 have

Auto-IDs.*

To use Auto Setup

1. Connect a probe to a channel.

2. Slide the [ON/OFF] switch to turn on power.

• This causes the Power lamp to light.

3. Press the [SET UP] key.

• This causes the Ready lamp to light.

The optional “Motion Sensor (EA-2)” does not have an Auto-ID.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio EA200 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info