Bedienungsanleitung Casio GP-510 (Seite 72 von 84) (Englisch, Spanisch)

723297

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

EN-70

Troubleshooting

Problem Cause Action See

Page

No sound is produced

when I press a keyboard

key.

1. The VOLUME controller is set to

“MIN”.

1. Rotate the VOLUME controller more

towards “MAX”.

 EN-7

2. Headphones or an adaptor plug is

plugged into one of the PHONES

jacks.

2. Disconnect whatever is connected to the

PHONES jacks.

 EN-68

3. MIDI Local control is turned off. 3. Turn on the Local control setting.  EN-49

4. The Speaker Out is set to Off. 4. Change the Speaker Out setting to “Auto”.  EN-48

5. The Keyboard Volume is set to 0. 5. Change the Keyboard Volume setting to

something other than 0.

 EN-46

The pitch of the Digital

Piano is off.

1. The Digital Piano’s key setting is

something other than “440.0Hz”.

1. Change the key setting to “440.0Hz”, or

turn Digital Piano power off and then back

on again.

 EN-46

2. Digital Piano tuning is incorrect. 2. Adjust Digital Piano tuning, or turn the

Digital Piano off and then back on again.

 EN-46

3. Octave shift is enabled. 3. Change the octave shift setting to 0.  EN-24

4. A non-standard temperament

setting is being used.

4. Change the temperament setting to

“00: Equal”, which is the standard modern

tuning.

 EN-25

Nothing happens when I

press a pedal.

1. The pedal unit cable is not

connected.

1. Connect the cable correctly.  EN-64

2. The pedal unit cable plug is not

plugged in completely.

2. Make sure that the pedal unit cable plug is

inserted as far as it will go into the pedal

connector on the bottom of the Digital

Piano.

Tones and/or effects sound

strange. Turning power off

and then back on again

does not eliminate the

problem.

Example:

Note intensity

does not change even

though I alter key pressure.

The “Auto Resume” feature is turned

on.

Turn off “Auto Resume”. Next, turn power off

and then back on again.

 EN-48

I cannot transfer data after

connecting the Digital

Piano to a computer.

– 1. Check to make sure that the USB cable is

connected to the Digital Piano and

computer, and that the correct device is

selected with your computer’s music

software.

 EN-59

2. Turn off the Digital Piano and then exit the

music software on your computer. Next,

turn the Digital Piano back on and then

restart the music software on your

computer.

I cannot store data to a USB

flash drive or load data

from a USB flash drive.

– See “Error Indicators”.  EN-58

It takes a long time before I

can use the Digital Piano

after I turn it on.

Digital Piano memory data was

corrupted because a data transfer

operation with a computer was in

progress the last time you turned off

the Digital Piano. When this

happens, the Digital Piano performs

a memory format operation the next

time you turn it on. You cannot

perform any other operation while a

format operation is in progress.

It takes about 20 seconds after you turn on

power to perform the memory format

operation. Wait until the format operation is

complete. Note that you should take care to

avoid turning off the Digital Piano while a data

transfer operation with a computer is in

progress.

 EN-59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio GP-510 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio GP-510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info