5
Operation Guide 5121
Auto Correction of Hand Home Positions
Strong magnetism or impact can cause the hands and/or day setting to be off, even
if the watch is able to perform the signal receive operation. Auto correction of hand
home positions correct the hand position automatically.
•
•
Hour Hand ,
Minute Hand , and
Second Hand . For the dial hands and day, you must perform the manual
adjustment procedure under “ Adjusting Home Positions Manually” .
•
–55 minutes to +5 minutes.
•
See “ To trigger auto correction of hand home positions” for more information.
•
complete.
•
under “ To trigger auto correction of hand home positions” or “ Adjusting Home
Positions Manually” .
To trigger auto correction of hand home positions
•
In the Timekeeping Mode, hold down D for about six
seconds until the
Second Hand completes one full
revolution.
•
Second Hand will stop momentarily about
three seconds after you hold down D , do not release the
button yet. Wait until the
Second Hand completes a full
revolution before you release D .
•
the Timekeeping Mode, press D again.
• D when the
Second Hand stops the fi rst
time (after about three seconds) in the above operation,
the watch will enter the home position adjustment mode,
which is described under “ Adjusting Home Positions
Manually” . If this happens, press A to return to the
Timekeeping Mode and then perform the above operation
again.
•
two steps.
watch.
timekeeping automatically. This completes the correction operation.
Adjusting Home Positions Manually
Strong magnetism or impact can cause the hands and/or date of the watch to be
off, even if the watch is able to perform the signal receive operation. If this happens,
perform the applicable home position adjustment procedures in this section.
•
correct.
•
positions of the
Hour Hand ,
Minute Hand , and
Second Hand .
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A . The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in the home position adjustment mode. In either case,
any adjustments you made before the watch returned to the Timekeeping Mode will
be applied.
To adjust home positions
C at least two seconds until the
Second
Hand stops and then starts moving again.
D for about three seconds.
•
Second Hand will start to move when you fi rst
press D . Keep D depressed until the
Second
Hand stops.
•
mode.
•
automatically if you do not perform any operation for
about two or three minutes.
•
Second Hand home position adjustment.
•
Second Hand moves to 12 o’ clock, it is in the correct home position. If it
doesn’ t, use D to move it to 12 o’ clock.
• C in the home position adjustment mode will cycle through the
adjustment settings as shown below.
Second
Hour/
Minute/
24-hour
Right Dial Hands
Left Dial Hand
Day
•
you move to a proper home position, you press B to move the setting back one
step. Next, press D again to return it to the home position. This helps to ensure
better home position adjustment accuracy.
fi rming that the
Second Hand is at the proper
home position, press C . This will switch to
Hour
Hand and
Minute Hand home position adjustment.
•
Hour Hand and
Minute Hand are at their
proper home positions if they both move to 12 o’ clock.
The
24-hour Hand also will move along with
Hour Hand movement, and cannot be adjusted
individually. If the hands are not positioned correctly,
use D (+) and B (– ) to move them to their proper
home positions.
fi rming that the
Hour Hand and
Minute
Hand are in their correct home positions, press C .
This will switch to
Right Dial Hands home position
adjustment.
•
Right Dial Hands are at their proper home positions if they both move to
24. If the hands are not positioned correctly, use D (+) and B (– ) to move them
to 24 .
B +
@
B +
* 6 5
@
B +
* 6
@
fi rming that the
Right Dial Hands are in the
correct home position, press C . This will advance to
Left Dial Hand home position adjustment.
•
Left Dial Hand is in the correct home position if
it is pointing at 12 o’ clock. If it isn’ t, use D (+) and B
(– ) to move it to 12 o’ clock.
fi rming that the
Left Dial Hand is in the
correct home position, press C . This will advance to
day home position adjustment.
•
Day is in the correct home position if it
shows 1 . If it doesn’ t, use D (+) and B (– ) to change
the day to 1 .
A to return to the Timekeeping Mode.
•
Day moves to the current day, and then the
Hour Hand and the
Minute Hand will move to the current time. Wait until everything stops moving.
Troubleshooting
Hand Movement and Position
I lost track of what mode the watch is in.
Refer to “ To select a mode” . To return directly to the Timekeeping Mode from any
other mode, hold down C at least two seconds.
The
Second Hand is moving at two second intervals.
All the watch’ s hands are stopped at 12 o’ clock and none of the buttons work.
Power may be low. Expose the watch to light until the
Second Hand starts moving
normally, at one-second intervals.
The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
•
•
receive operation.
•
Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode. Do not perform any operation until the
hands return to their normal positions (in about 15 minutes). The hands should return
to their correct positions when power recovers. To help power recover, leave the
watch in a location where it is exposed to light.
■
Your Home City setting may be wrong. Check your Home City setting and correct it,
if necessary.
The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is
possible, see “ To confi gure Home City settings” .
If you are using the watch in an area where time calibration signal reception is not
possible, you may need to change your Home City’ s STD (standard time)/DST
(daylight saving/summer time) setting manually. Use the procedure under “ To toggle
the Home City time between standard time and daylight saving time” to change the
STD/ DST setting.
The hands and/or day indications are off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day alignment. Adjust the watch’ s
hand and day home position alignment.
World Time Mode
The World Time indicated by the
Right Dial Hands in the World Time Mode is
one hour off from the actual time in the selected World Time City.
The STD (standard time)/DST (daylight saving/summer time) setting of the selected
World Time City may be wrong. Select the correct STD (standard time)/DST (daylight
saving/summer time) setting.
The World Time indicated by the
Right Dial Hands in the World Time Mode
is off.
Your Home City settings may be wrong. Check your Home City settings and correct
them, if necessary.
Charging
The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3. Continue exposing the watch
to light until the
Second Hand starts moving normally (at one-second intervals).
The
Second Hand starts to move at one-second intervals, but then suddenly
returns to moving at two-second intervals.
The watch probably is not suffi ciently charged yet. Continue keeping it exposed to
light.
Time Calibration Signal
The information in this section applies only when LON , PAR , ATH , HNL , ANC , LAX ,
DEN, CHI, NYC, HKG, or TYO is selected as the Home City. You need to adjust the
current time manually when any other city is selected as the Home City.
The
Second Hand indicates NO (N) when I check the result of the latest
receive operation.
Possible Cause Remedy
•
or performing a button operation during
the signal receive operation.
•
reception conditions.
Keep the watch in an area where reception
conditions are good while the signal receive
operation is being performed.
You are in an area where signal reception
is not possible for some reason.
See “ Approximate Reception Ranges” .
The calibration signal is not being
transmitted for some reason.
Check the website of the organization that •
maintains the time calibration signal in your
area for information about its down times.
Try again later.•
The current time setting changes after I set it manually.
You may have the watch confi gured for Auto Receive of the time calibration signal,
which will cause the time to be adjusted automatically according to your currently
selected Home City. If this results in the wrong time setting, check your Home City
setting and correct it, if necessary.
6
5
