Bedienungsanleitung Casio KL100 (Seite 15 von 24) (Englisch)

506029

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

E-14

Type

ST-15

ExampleMaximum Stamp Size

5.5cm

Tape

Backing

XYZ

3. Use H and J to move the cursor to the style you want to use.

4. When the cursor is located under the style you

want to specify, press SET to select it and re-

turn to the text display.

Note

• You could also perform the above procedure in reverse, specifying the char-

acter style first and then inputting the text.

Part 6 Printing

This part of the manual includes all the information you need to print tapes. It

also tells you how to print special stamp tapes that you can attach to an optional

stamp holder to create your own original stamps.

Printing Precautions

• Never turn power off while printing is being performed.

• Make sure that the tape outlet is not blocked before you start printing.

• Never operate the tape cutter while printer is being performed (indicated by

the message “PRNT” on the display).

• During printing at very high density, printing of very long text, or repeat print-

ing of the same text a number of times, the Label Printer may stop printing for

about five seconds. This is not a malfunction, and normal printing should

resume shortly (indicated by the message “P R N T” on the display).

Important!

• Never touch the tape cutter while a tape cut operation is being performed.

Doing so can result in cuts and other personal injury.

Printing a Tape

Printing a tape is as easy as pressing the PRINT key.

To print a tape

1. Press the PRINT key to print a tape of the text you have input and laid out.

• To stop a print operation that is in progress, press ESC.

2. After the print operation is complete, press down on the tape cutter button to

cut the tape.

3. Use scissors to trim the tape to the size you want, if necessary.

• After you print a tape, you can peel off its paper

backing and stick the tape onto the object you

want. Note that the tape will not stick on coarse,

wet, oily, or soiled surfaces. Also, you should not

try to use the tape where it is exposed to direct

sunlight or rain. Do not stick the tape onto hu-

man skin.

• An easy way to remove the backing from a tape

and expose the adhesive surface is to bend the

tape near one of its ends. This should cause the

tape and its backing to separate, allowing you to

pull them apart.

Stamp Printing

The stamp printing feature lets you print on special stamp tape. You can then

attach the finished stamp tape to an optionally available stamp holder to create

your own original pre-inked stamps. The following is the type of stamp holder

currently available for use with stamp tapes.

Note the following important points about stamp printing.

• Stamp printing prints text in mirror image.

• Stamp printing is impossible while 6mm is specified as the tape width.

• An error message (ERR!) appears on the display and the Label Printer refuses

to print whenever you try to print text that is longer than the maximum length

you specify.

8.9cm

5.5cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio KL100 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info