Bedienungsanleitung Casio KL7200E (Seite 7 von 29) (Englisch)

506036

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

E-6

Replacing Batteries

A handy low battery power indicator lets you know when battery power is getting

too low for proper operation. The message “LOW BATTERY” appears on the

display if battery power is low when you perform any of the following operations.

• Turn power on

• Execute a print operation

Whenever the “LOW BATTERY” message appears, press SET to clear it from

the display. You should still be able to perform some Label Printer operations,

but some power intensive operations (like printing) may become impossible if

battery power is too low. In any case, you should replace batteries as soon as

possible or switch to the AC adaptor as soon as possible after the “LOW

BATTERY” message appears.

Important!

• All data stored in memory is deleted whenever batteries go dead and when you

replace batteries. Be sure to keep written backup copies of all important data.

• Batteries can burst or leak and damage your unit if you do not use them

correctly. Note the following important points.

• Be sure that the plus (+) and minus (–) sides of each battery are facing correctly.

• Never mix batteries of different types.

• Never leave dead batteries in the Label Printer.

• Remove the batteries if you do not plan to use the Label Printer for a long

time.

• Replace the batteries in accordance with the battery life marked on the side

of the battery.

Warning!

• Never use recharged batteries with the unit.

• Do not expose batteries to direct heat, do not short circuit them, and do not

try to take them apart.

•

Keep batteries out of the reach of small children. If swallowed, consult

with a physician immediately.

• Be sure to replace the batteries in accordance with the battery life printed on

the side of the battery itself.

To load the batteries

1. Turn power off.

• If you are using the optional AC adaptor for power, you should also unplug it

from the Label Printer.

2. Open the battery compartment cover on the

back of the Label Printer by sliding it in the

direction indicated by the arrow.

3. If you are replacing batteries, remove all six of

the old batteries.

4. Load a set of six new batteries into the battery compartment, making sure

that their positive (+) and negative (–) ends are facing in the correct directions.

Be sure to use alkaline batteries.

5. Replace the battery compartment cover.

AC Adaptor

Note the following important precautions when using an AC adaptor to power

your Label Printer.

• Use only a genuine CASIO AD-A95100 AC adaptor with the same voltage

rating as the household current in your area. Using a wrong adaptor can

damage your Label Printer.

• Be sure to turn the Label Printer off before you connect the adaptor. Do not

turn power on until the adaptor is connected to the Label Printer and plugged

into and AC outlet.

• Be sure to unplug the AC adaptor from the AC outlet whenever you are not

using the Label Printer.

AC Adaptor Cap

Remove the ADAPTOR CAP before connecting

the AC adaptor.

ADAPTOR

CAP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio KL7200E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio KL7200E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info