506032
20
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
E-19
Type
ST-15
ExampleMaximum Stamp Size
5.5cm
10mm
5.5cm
9.3cm
18mm
Part 8 Stamp Printing
The stamp printing feature lets you print on special stamp tape. You can then
attach the finished stamp tape to an optionally available stamp holder to create
your own original pre-inked stamps. The following is the type of stamp holder
currently available for use with stamp tapes.
Note the following important points about stamp printing.
Stamp printing prints text in mirror image.
You can perform stamp printing only when 18mm is specified as the tape width.
An error message LENGTH ERROR! appears on the display and the Label
Printer refuses to print whenever you try to print text that is longer than the
maximum length you specify.
To print a stamp tape
1. Input the text you want to print.
2. Press FUNC and then 2 (STAMP).
PRIN
S
T
E
?
T ESC
3. Press SET to print the stamp tape or ESC to abort the print operation and
return to the text input display in step 1.
After the printing is complete, the Label Printer returns to the input display in
step 1.
4. Cut off the tape and affix it to the optional stamp holder.
See the instructions that come with the optional stamp holder for information
about how to attach the stamp tape.
Part 9 Memory
This part of the manual tells you how to store text data in memory for instant
recall when you need it. You can store one block of text in memory, containing
up of 95 characters.
Important!
All data stored in memory is deleted whenever batteries go dead and when
you replace batteries. Be sure to keep written backup copies of all important
data.
When using the optional AC adaptor, never disconnect the adaptor while
batteries are not loaded in the Label Printer or when batteries are dead. Doing
so causes all data stored in memory to be deleted.
To store data
1. Input the text you want to store.
2. Press FUNC 3 (MEMO).
3. Press z and x to select STORE.
S
R
T
E
O
C
R
A
E
LL
4. Press SET to store the text in memory or ESC to abort the store procedure
without storing anything.
COMPLETE
If there is nothing in memory yet, pressing SET stores your text.
If there is already text stored in memory, the message OVERWRITE? SET/
ESC appears when you press SET. Press SET again to replace the existing
text with the new text, or ESC to cancel the store operation.
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

casio-kl780

Suche zurücksetzen

  • Data error- was tun, damit er wieder ausdruckt..
    Mit freundlichem Gruß A. Rehe Eingereicht am 7-11-2018 13:07

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio KL780 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Casio KL780

Casio KL780 Bedienungsanleitung - Deutsch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info