Bedienungsanleitung Casio PL-40R (Seite 16 von 50) (Englisch)

466869

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Using the Mixer

E-48

6. Use the [+] and [–] buttons or the selector dial to

change the setting of the currently selected

parameter.

 Press the EXIT/NO button to return to the part

selection screen in step 3 of this procedure.

 Any time during the above procedure, you can

select another part by pressing the PART/

(MIXER) button.

7. Repeat steps 2 through 6 to change the settings

of other parameters if you want.

 When changing parameter settings, you can play

notes on the keyboard as you change parameter

settings to see what effect your settings have.

8. After you are finished making the settings you

want, press the EXIT/NO button.

This section provides detailed explanations of each of the

mixer parameters, and their setting ranges.

J Tone: 271

This parameter controls the tones assigned to each part.

 You can also change the tone assignment with the TONE

buttons. The tone you select is applied to the currently

selected part.

 Use DRUM tone group values for the “Drum” and

“Percussion” parts.

 You cannot select DRUM tone group values for “Bass”, or

“Chord” parts.

 Changing the tone assigned to the Upper1 also changes

the tone assigned to Harmo1. Changing the tone assigned

to the Upper2 also changes the tone assigned to Harmo2.

J Part On/Off: On, Off

This parameter can be used to turn each part on (sounds) and

off (does not sound). The current on/off status of a part is

indicated by the on-screen level meter. See “Level Meter

Screen” on page E-13 for more information.

J Volume: 0 to 127

This parameter adjusts the overall volume of each part.

J Pan: –64 to 63*

Use this parameter to adjust the pan setting (volume balance

between the left and right speakers). A value of 0 puts the

speakers in balance, so the stereo center is halfway between

the two speakers. A smaller value shifts the stereo center left,

while a larger value shifts it right.

* When “On” is selected for the DSP you are using, these

settings are applied in accordance with each DSP

parameter setting.

The mixer lets you control the effects applied to each

individual part, making it different from the Effect Mode,

whose settings are applied to all parts in general.

J Reverb Send: 0 to 127

This parameter controls how much reverb is applied to a part.

A setting of 0 turns reverb off, while a setting of 127 applies

maximum reverb.

J Chorus Send: 0 to 127

This parameter controls how much chorus send is applied to

a part. A setting of 0 turns chorus send off, while a setting of

127 applies maximum chorus send.

 “Chorus Send” does not work with drum sounds.

J DSP: On, Off

You can use this parameter to turn DSP off for a particular

channel, or to turn it on.

Mixer Parameters

Tone Parameters

Effect Parameters

426-E-050A

PL40NE01-1.book 48 ページ２００２年７月２３日　火曜日　午後６時５２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio PL-40R Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio PL-40R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info