Bedienungsanleitung Casio QW5526 - MRG-B1000D G-shock (Seite 16 von 21) (Englisch)

740164

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Press (C).

Confirm that the small hour and minute

hands, and the small 24-hour hand are all

stopped at 12 o’clock.

Small minute handSmall hour hand

Small 24-hour hand

If the small hour and minute hands, and

the small 24-hour hand are not at 12

o’clock, rotate the crown to align them

correctly.

Press (C).

Confirm that the mode hand is stopped at

12 o’clock, and check if the day is

indicated properly.

Day (Operation start day)

Mode hand

If the mode hand and or the day indicator

is out of alignment, rotate the crown to

move the mode hand to 12 o’clock and the

day to the center of the indicator window.

●

The movement range of the mode hand

and day indicator is limited when you

rotate the crown. The maximum left-

right movement of the mode hand is 180

degrees in either direction. The day

indicator moves only slightly.

●

After the mode hand and day indicator

are in the positions you want, advance

to step 9 of this procedure. If you are

unable to make the adjustments you

want, go to step 7.

Press (C).

Confirm that the day indicator shows 1.

Day

●

Changing the date setting will cause the

mode hand to rotate repeatedly. In

some cases, the mode dial may

continue to rotate for about 5 minutes.

Hand and Day Indicator Movement

If 1 is not shown for the day, rotate the

crown until 1 is shown for the day.

●

The mode hand moves in conjunction

with crown rotation. Move the mode

hand to 12 o’clock.

Push the crown back in.

Note

●

Leaving the crown pulled out for more

than approximately 30 minutes without

performing any operation will

automatically cause the adjustment

operation to become disabled. If this

happens, push the crown back in to its

normal position and then pull it out

again to restart the procedure from the

beginning. Pushing the crown in to its

normal position part way through the

alignment procedure will cause the

hands to return to their normal position.

Any alignment you performed up to

that point will be applied.

Moving to Another Time

Zone

Use the procedure below to easily change day

and time settings of the watch to a destination

location.

●

Before Boarding

Configure the World Time (Dual Time)

setting to the current time at your

destination.

Destination time

Current time

Using MR-G Connected to Configure

Settings

Using Watch Operations to Configure

Settings

Disable auto time adjustment.

Using MR-G Connected to Configure

Settings

Using Watch Operations to Configure

Settings

●

After Arriving

Swap the origin time zone time with the

destination time zone time.

After swappingBefore swapping

Destination time

Using MR-G Connected to Configure

Settings

Using Watch Operations to Configure

Settings

Enable auto time adjustment.

Using MR-G Connected to Configure

Settings

Using Watch Operations to Configure

Settings

Operation Guide 5526

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio QW5526 - MRG-B1000D G-shock Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info