Bedienungsanleitung Casio TE3000S (Seite 52 von 120) (Englisch)

40909

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Advanced Operations

This chapter describes more sophisticated operations that you can use to suit the needs of your retail

environment.

Stock check

Each PLU has an actual stock totalizer that you can program with a minimum stock quantity. Then the register

checks actual stock quantities against the programmed minimum stock quantities. Stock operations are

performed only for PLUs (except scanning PLUs) programmed with minimum stock quantities.

Stock warnings

The cash register checks for negative values in actual stock quantities during the registration itself. After

registration is complete, it checks actual stock quantities against minimum stock quantities. The following

warning indicators are used to inform the operator of any problem.

• Negative stock:

This indicates that the actual stock quantity is negative. You can also program the cash register to treat this

condition as an error. This warning does not appear when the actual stock quantity is zero.

• Under minimum stock:

This indicates that the actual stock quantity is less than or equal to the minimum stock quantity. The cash

stock quantity.

Notes

• The stock check operation is also performed for PLUs programmed with minimum stock quantities that make

up set menus.

• None of the warning indicators appear unless the cash register is specifically programmed for the stock check

operation.

• Stock operations can be performed for registrations in the RF mode or those performed with <REFUND> (the

refund key).

• An error correct, void, or cancel operation restores the original of items in stock value.

Clerk interrupt function

There are two types of clerk interrupt function, illustrated by PROCEDURE 1 and PROCEDURE 2 below.

• In PROCEDURE 1, each clerk possesses a unique clerk interrupt buffer, and so the clerk interrupt function

gives each individual clerk the ability to perform an independent registration operation. In this case, each clerk

is individually linked to a unique clerk interrupt buffer.

• In PROCEDURE 2, multiple clerks use the same clerk interrupt buffer, and so a single clerk interrupt

operation (clerk change during registration) can be performed any registration is in progress. In this case,

multiple clerks are linked to a single clerk interrupt buffer.

Note the following important points concerning the clerk interrupt function.

• The register must be programmed to allow use of the clerk interrupt function.

• To use the clerk interrupt function, a clerk interrupt buffer must first be allocated with the memory allocation

operation. Next the manager control operation (X1 mode) should be used to perform clerk assignment for the

clerk interrupt function. The clerk interrupt operation cannot be performed by clerks who are not linked to a

clerk interrupt buffer.

• You cannot use the clerk interrupt function on a register set up to function as part of a check tracking system.

In the REG1, REG2, and RF modes, clerks can be change while a transaction is in progress, making it possible

for multiple clerks to simultaneously perform registrations using a single register.

For example, if clerk 1 is interrupted while registering a transaction, clerk 2 can use the same machine to

interrupted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio TE3000S Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio TE3000S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info