Bedienungsanleitung Casio WK-1630 (Seite 52 von 96) (Englisch)

586841

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

E-50

Saving an Edited Pattern

• The 10 rhythm numbers 120 through 129 make up the user rhythm

area, where you can store your original rhythms. You can recall a

user rhythm with the same operation as that for recalling a built-in

pattern, and you can even use a user rhythm pattern as the base for

creating a new rhythm pattern.

• The keyboard comes with a built-in lithium battery that supplies

power to the memory to retain memory contents while keyboard

power is turned off. See “Power Requirements” on page E-15 for

important information about the lithium battery.

• You can use the keyboard’s MIDI capabilities to save your original

accompaniment patterns to a computer or other external storage

device. See “Bulk Sending Keyboard Data” on page E-65 for de-

tails.

• With the WK-1800, you can use the built-in disk drive to save orig-

inal accompaniment patterns to diskette. See “Using the Floppy

Disk Drive (WK-1800 Only)” on page E-67 for details.

• You can store up to 10 accompaniment patterns in the user area,

but the actual number of patterns you will be able to store depends

on their sizes. If the patterns you store are relatively large, memo-

ry become full after fewer than 10 patterns are stored.

Using the Pattern Create Mode

This section describes how to use the Pattern Create Mode to create

an original accompaniment pattern.

IMPORTANT!

The procedures in this section all assume that you have read and are

familiar with the information under “Pattern Sequencer Basics” on

page E-48, and that you already know how to navigate between Pat-

tern Sequencer modes.

❚

NOTE

❚

Be sure to save your work whenever you quit an accompaniment pattern

creation session. See “Exiting the Pattern Sequencer Mode” on page E-56

for details.

Pattern Creation Techniques

You can use either of the two following techniques to create an ac-

companiment pattern.

• Base Pattern Editing

While playing back the part of a built-in pattern or previously cre-

ated user pattern, you can add or delete notes, or completely de-

lete a part and replace it with a new one.

• From Scratch

With this method, you must input all the parts for all the elements

you want to use. With this method, you must use the procedure

under “Work Area Clear” on page E-54 to clear the Pattern Sequenc-

er work area before you start recording.

The record procedure is identical, no matter which of the above meth-

ods you use.

The following procedure tells you how to play back individual ele-

ments of the accompaniment pattern currently stored in the Pattern

Sequencer work area. If you are going to use the base pattern editing

method described above, you can use this procedure to become fa-

miliar with all the parts that make up the pattern before you actually

start editing it.

To play back elements of the accompaniment

pattern in the work area

While the Pattern Sequencer is turned off, press the

PATTERN button once to enter the Pattern Create

Mode.

Select the element you want to play back.

• The Normal element is always selected first when you ini-

tially turn on the Pattern Sequencer.

• Use the following buttons to select the other elements.

NORMAL/FILL-IN ...... Toggles between Normal and Nor-

mal Fill-In elements.

VARIATION/FILL-IN .. Toggles between Variation and Vari-

ation Fill-In elements.

INTRO ............................. Selects Intro element.

SYNCHRO/ENDING ... Selects Ending element.

Press the START/STOP button.

• The selected element plays in a loop, repeating itself.

• The display shows measure and beat numbers during ele-

ment playback.

• You can perform the following operations during element

playback.

• Tempo changes

• Part on and off

• Mixer operations*

• Tone operations*

To stop playback, press START/STOP again.

*1 The cursor keys and ENTER button function as Mixer operation

buttons during playback. Auto Accompaniment uses internal chan-

nels CH6 through CH10, which can be used when making part

settings. See “Changing the Parameters of a Channel” on page E-

30 for details on using the Mixer to make settings.

*2 You can change the tone setting by pressing TONE button, and

then using the number keys, [+], and [–] to specify a tone number.

The Pattern Sequencer turns off automatically if you do not per-

form any operation for about five seconds. You can change the

tone settings of each part inside each element.

❚

NOTES

❚

• Pressing the PATTERN button while a pattern is playing stops accom-

paniment playback and enters the Pattern Edit Mode.

• Use the Mixer to adjust the volume balance between channels. First set

the Global Volume parameter to 127. Next, adjust the Expression pa-

rameter volume balance. See “Additional Channel Mode Parameters”

on page E-31 for details.

733A-E-052A

Indicates the Pattern

Create Mode.

Indicates the currently

selected element.

Original Key

AMPENVELOPE

00 FLAT

01-17 VIBRATO

18-45 OTHERS

DECAY

SUSTAIN

PITCHENVELOPE

MIN

MAX

FULL RANGE

CHORD

CASIO CHORD

SONG

FINGERED

PATTERN

EXTERNAL

INTERNAL

UPPER1

CH 1

UPPER2

CH 2

LOWER1

CH 3

LOWER2

STOREBANK

CH 4

ACC VOL.

CH 5

CHORD1

CH 6

CHORD2

CH 7

CHORD3

CH 8

BASS

CH 9

RHYTHM

CH 10

TR1

CH 11

TR2

CH 12

TR3

CH 13

TR4

CH 14

TR5

CH 15

TR6

CH 16

789

456

PARAMETER RESET:

DELETE

/YESS/NO

MAIN MANU/

CHANNEL VOLUME:

SUB MANU/

CHANNEL SELECT:

–]

WK-1800/1600(E)-48~57 03.7.31, 5:21 PMPage 50 Adobe PageMaker 6.5J/PPC

Casio WK-1630 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info