Bedienungsanleitung Casio WK-3700 (Seite 46 von 132) (Englisch)

466911

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

E-44

The Synthesizer Mode of this keyboard provides the tools

for creating your own original tones. Simply select one of the

built-in tones and change its parameters to create your own

original sound. You can even store your sounds in memory

and select it using the same procedure as that used to select a

preset tone.

Synthesizer Mode Functions

The following describes how to use each of the functions

available in the Synthesizer Mode.

Synthesizer Mode Parameters

The preset tones that are built into this keyboard consist of a

number of parameters. To create a user tone, you first recall a

advanced tone (000 to 331) or a preset tone (400 to 599) and

then change its parameters to change it to your own tone.

Note that drum set tones (600 through 617) cannot be used

as the basis of a user tone.

The illustration nearby shows the parameters that make up

the preset tones and what each parameter does. As can be

seen in the illustration, parameters can be divided into four

groups, each of which is described in detail below.

NOTE

• Note that the tone whose parameter you can edit is the

one assigned to the channel (1 through 4) that is currently

selected with the Synthesizer Mode.

Synthesizer Mode

Volume Characteristic

Parameters

쎲Attack Time

쎲Release Time

쎲Cutoff Frequency

쎲Resonance

Tone Pitch Parameters

쎲Vibrato Type

쎲Vibrato Delay

쎲Vibrato Rate

쎲Vibrato Depth

쎲Octave Shift

Tone Characteristic

Setting Parameters

쎲Level

쎲Touch Sense

쎲Reverb Send

쎲Chorus Send

쎲DSP Line

쎲DSP Type

쎲DSP Parameter

Output

Tone Characteristic

Waveform

Tone Setting

(1) Tone Characteristic Waveform

■

Tone Setting

Specifies which of the preset tones should be used as the

original tone.

(2) Volume Characteristic Parameters

These parameters control how the tone changes over time,

from when the keyboard key is pressed until the tone decays.

You can specify changes in volume and sound characteristics.

■

Attack time

This is the rate or time it takes for the tone to reach its highest

volume level. You can specify a fast rate, where the tone

reaches its highest volume level immediately, a slow rate

where it gradually rises, or something in between.

■

Release time

This is the rate or time it takes for the tone volume to fall to

zero. You can specify a release that ranges from a sudden fall

to zero, to one that gradually falls to zero.

■

Cutoff Frequency

The cutoff frequency is a parameter for adjusting timbre by

cutting any frequency that is higher than a specific frequency.

A larger cutoff frequency produces a brighter (harder) timbre,

while a smaller frequency produces a darker (softer) timbre.

Time

Note ends

Key pressed

A R

Key released

Envelope

A: Attack time

R: Release time

Level

Cutoff frequenc

Frequency

738A-E-046A

WK3200_e_40-50.p65 05.3.15, 6:17 PM44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio WK-3700 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio WK-3700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info