Bedienungsanleitung Casio xj s52 super slim projector (Seite 6 von 40) (Englisch)

215430

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

E-6

Operating Precautions

z Never touch the glass of the lamp with your fingers. Doing so can damage the lamp and

shorten its life.

z The light source lamp is a consumable item. The average life of a lamp is approximately

2000 hours. After 2000 hours, a message appears to alert you to the need of lamp

replacement. However, note that the characteristics of a particular lamp or lamp operating

conditions can cause the lamp to start to go dim or even fail before the message appears.

z Lamps are guaranteed for 180 days from the date of purchase or for 500 hours operation,

whichever comes first.

z A mercury lamp with high internal pressure is used as the light source. A lamp that is

weakened by impact, damage, or expiration of its lamp life may explode or fail to light if

exposed to loud noise. Note that lamp life differs greatly from lamp to lamp, and is affected

by conditions under which the lamp is used.

z The replacement message appears and the LAMP indicator flashes red after the lamp life is

reached. When this happens, replace the lamp using the instructions provided in this User’s

Guide.

z If the lamp continues to be used after its lamp life is reached, after 100 hours the projector

will enter a cool down state and then go into standby. The projector will not turn on again

until you replace the lamp.

z When the lamp life is reached, the message “It is time to replace the lamp. Use the

procedure in the User’s Guide to replace the lamp as soon as possible.” appears on the

display for about 10 seconds, and the LAMP indicator starts to flash red in one-second

intervals. Replace the lamp as soon as possible after the message appears or the LAMP

indicator flashes.

z Replace the lamp with a special replacement lamp, which should be available from your

original dealer. Use only the lamp type that is specified for this projector.

z Turn off the projector. After the POWER/STANDBY indicator changes to steady (not flashing)

amber, unplug the projector from the power outlet. Next, wait for at least 60 minutes before

removing the lamp. Note that the lamp cartridge becomes very hot during normal use and

during standby. Handling it when hot creates the risk of burn injury.

z The lamp contains mercury. Dispose of old lamps in accordance with the rules and

regulations of your local jurisdiction.

z When replacing the lamp, use the special screwdriver that comes with the replacement lamp.

Lamp Handling Precautions

Caution

Continued use of a lamp that has passed its lamp life increases the risk of

the lamp rupturing. Replace the lamp with a new one as soon as possible

after the replacement message appears.

Lamp Replacement Precautions

XJ-S32/XJ-S37 Replacement Lamp YL-3A

XJ-SC210/XJ-SC215/

XJ-S42/XJ-S47 Replacement Lamp

YL-4A

XJ-S52/XJ-S57 Replacement Lamp YL-5A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio xj s52 super slim projector Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info