Bedienungsanleitung Casio XJ-SK600 (Seite 14 von 19) (Englisch)

543646

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

E-13

Getting Ready

8. On the “Image Shaping” menu that appears, select “Adjust Image Position” and

then press the [ENTER] key.

z This will project two adjustment patterns, a yellow one for Projector A and a light blue one for

Projector B.

z Use the focus rings of Projector A and Projector B to adjust the focus of the patterns as required.

Important!

z All of the explanations in this manual assume that Projector A is connected by HDMI cable to

OUTPUT A of the Control Box and that Projector B is connected to OUTPUT B, as shown under

“Wiring” (page E-7). Reversing these connections will cause the adjustment pattern colors to be

reversed (light blue for Projector A, yellow for Projector B).

9. Observe the adjustment patterns as you adjust Projector A and then Projector B.

Try to achieve the characteristics described below as you make adjustments.

z Adjust so the horizontal crosshairs of the adjustment patterns are horizontal.

z Adjust so the vertical lines of the adjustment pattern crosshairs are in the center of the screen.

10.

On the Control Box remote controller, press the [BLANK] key.

z This will cause the Projector B adjustment pattern to disappear, leaving only the Projector A

adjustment pattern (yellow).

11.

While observing the Projector A adjustment pattern, perform the vertical

adjustments described below.

z Adjust the vertical orientation of the cabinet.

z Adjust the zoom ring of Projector A.

The crosshairs of the adjustment pattern should be in the center

of the target screen and the outer border of the adjustment

pattern should be just outside of target projection area, as

shown in the nearby figure.

12.

Press the remote controller’s [BLANK] key.

z This will project from Projector B again so the adjustment patterns of both Projector A and

Projector B are being projected.

13.

Perform the steps below to get the adjustment pattern of Projector B as closely

aligned as possible with the Projector A adjustment pattern.

z Take care simply to loosen the five screws. Do not remove them.

14.

After the adjustment is the way you want, press the [ESC] key.

z This will cause the Projector A and Projector B adjustment patterns to disappear, and project the

“Image Shaping” menu.

Projector A : Use the same procedure as that in step 3 to fine tune the adjustment of the

Projector A adjustment pattern.

Projector B : Use the same procedure as that in step 5 to fine tune the adjustment of the

Projector B adjustment pattern.

(1) Adjust the zoom ring of Projector B.

(2) Loosen the five screws that secure the cabinet side panels (see the illustration under step 5,

above), and then rotate the adjuster knob to adjust the orientation.

(3) After position adjustment is complete, fully tighten the screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio XJ-SK600 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio XJ-SK600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info