Bedienungsanleitung Casio XW-P1 (Seite 31 von 96) (Englisch)

585756

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Selecting and Creating Tones

E-29

■ Block (10): Controllers Editable Virtual Controller Parameters

These controllers are virtual controllers for adjusting any editable parameters (destinations) with any input method (source).

Preparation

Perform the following steps from the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page

E-21.

Select “VirtualCtrl >Ent” and then press

ENTER to enter the group.

• Controllers are numbered 1 through 8, and are assigned to the

sliders (1/9 through 8/16).

Use the

PART minus (–) and plus (+) buttons to select the number of the controller you want to edit.

Editable Parameter List

■ Other Editable Items

This section explains parameters that are not part of the blocks described up to this point. These settings not only apply to the Solo

Synthesizer, but also to other category tones as well.

Preparation

Display the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page E-21.

Editable Parameter List

• Shaded cells indicate a group made up of multiple items. Press

ENTER to display the items that make up a group.

Display Text Description Settings

Source

Source. Specifies the input method.

Off: None

CC00 to CC97: MIDI control change*

NoteOnKeyNum: Key number of MIDI note on message

NoteOnVel: Velocity value of MIDI note on message

Ch.Pressure: MIDI channel after touch

Bend Up: Upward operation from

BENDER center

Bend Down: Downward operation from

BENDER center

Modulation:

MODULATION operation

LFO1: LFO1 (Block (8))

LFO2: LFO2 (Block (9))

* For details about each setting, refer to the MIDI Implementation document

(http://world.casio.com/) and other MIDI documentation.

Refer to the cell to the

left.

Depth Depth. Specifies how virtual controller is applied. –128 to 0 to +127

Dest Destination. Specifies the destination parameter for a virtual controller operation.

•Off

• Block (1) to (9)

parameters (pages

E-24 through E-28)

whose “Display Text”

items have “(V)” after

them.

• DSP parameters (page

E-88)

Display Text Description Settings

DSP On/Off

(Non-Solo

Synthesizer

tones only)

DSP on/off. Specifies whether or not DSP should be applied to tones.

• When this setting is on, pressing

ENTER enters the DSP editing screen (page E-39).

• This item is not displayed on the Solo Synthesizer tone editing list.

Off, On

DSP Edit >Ent

DSP edit. Group of editable effect function DSPs (page E-37). Press

ENTER to advance to the

DSP editing screen.

Disabled when the above DSP On/Off setting is off.

Volume Volume. Specifies the main volume. 0 to 127

Rev.Send Reverb send. Specifies how reverb (page E-37) is applied to a tone. 0 to 127

Cho.Send

(Non-Solo

Synthesizer

tones only)

Chorus send. Specifies how chorus (page E-37) is applied to a tone.

• This item is not displayed on the Solo Synthesizer tone editing list.

0 to 127

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio XW-P1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio XW-P1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info