Bedienungsanleitung Cata IT 773 (Seite 20 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

740827

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

time by operating the ON/OFF key. This is also valid if the control

has been locked (activated child safety feature).

The ON/OFF key has always priority in the switch-OFF function.

Automatic switch-OFF

When the control is ON it automatically sw itches-OFF after

20 seconds if no cooking zone or select key has been operated

within this period of time. If case of a cooking zone selection,

the automatic switch- OFF time is composed of 10 seconds

deselection time for a cooking zone at setting“0“ and 10 seconds

switch-OFF time.

Switching a cooking zone ON and OFF

First place the pan in the chosen cooking zone. If the pan is not

present the system cannot be switched on the correspondent

zone.

If the touch control is switched on, the cooking zone can be

selected by pressing the button (4) of the corresponding zone.

The display (5) of the zone selected lights up, while the remaining

displays are dimmed. if the cooking zone is “hot”, “H” and “0”

are alternately displayed.

Press the PLUS (3) or MINUS (2) button to select a setting and

the zone will begin to heat up.

Once the cooking zone has been selected, the setting can be

selected by keeping the PLUS (3) button pressed down. The

setting begins at level 1 and increases by 1 level every 0.4

seconds. When setting “9” is reached, the setting will not be

changed further.

If the setting level has been selected using the MINUS (2) button,

the start level is “9“ (maximum level). Keep the button pressed

down to lower the active level by 1 every 0.4 seconds. When

setting “0” is reached, there will be no further setting changed.

The setting can only be changed by pressing the MINUS (2) or

PLUS (3) button again.

Switching a cooking zone off

Select the zone to be switched off using the corresponding

button (4). The display (5) of the zone selected lights up, while

the remaining displays are dimmed. Press the Cooking zone (4)

and MINUS (2) buttons at the same time and the setting level of

the zone is changed to 0. Alternatively, the MINUS button (2) can

be used to reduce the setting level to 0.

If a cooking zone is “hot”, “H” and “0” will be alternately

displayed.

Switching-OFF all cooking zones

Immediate switching-OFF of all cooking zones can be achieved

anytime by means of the ON/OFF key. In the standby- mode

an “H“ appears on all cooking zones which are “hot“. All other

cooking zone displays are not illuminated.

Wattage settings

The output of the cooking zones can be set in 9 steps which

are indicated by the gures “1“ thru “9“ by means of LED

sevensegment-displays.

In the cooking zone located on the front left, when selecting

the power level 9 and after 30 minutes operating, the power

will decrease slightly for safety reasons. In case more power is

required, select the boost level (“P”)

Boost function

After selection of a respective cooking zone, the boost function

can be activated by selecting the power level 9 and then pressing

PLUS (3) button . By means of this function certain cooking

zones are enabled to receive power over the nominal (the number

of boostable cooking zone depends on the power available on a

partial modules which is to be lees than total hob power ). If the

desired cooking zone has the capacity to activate the booster,

the display shows a “P“ symbol. In case the available power is

not enough the cooking stage display ashes for 3 seconds on

the cooking zone which needs to be reduced and which requires

automatic adjustment.

The boosting time is limited to 5 min to protect cooking utensils.

After the booster is switched off automatically, the cooking zone

continues operation on power level “9”. The booster can be

reactivated after some minutes.

In case that the pan is removed from the cooking zone during

boosting, the boosting function remains active and boosting

time continues.

The power management is based on on the principle that the

last entry is requested by the induction as top priority. That

means that previous actions and settings also made for the other

cooking zones are reversed automatically, if necessary.

If induction identies the necessity of reducing power at a

cooking zone, the selected cooking stage ashes on that

cooking zone providing a correction period of 3 sec before the

power is reduced automatically to a minimum cooking stage.

If the setting is adjusted within the correction period, the power

management checks the settings again. Should a new setting lead

to further power reduction, the correction period starts again.

- If no automatic correction needs being made to the cooking

zone setting, the ashing stops immediately and the original

value remains as a steady display indication. Should the

situation change again on the power reduced cooking zone, no

automatic power increase is effected.

Residual heat indicator

It is meant to indicate to the user that the glass ceramic has

a dangerous touch temperature in the circumference of a

cooking zone. The temperature will be determined following

a mathematical model and the remaining residual heat will be

indicated by means of “H” on the corresponding 7-segment

display.

Heating-up and cooling down will be calculated dependent on:

· the selected setting („0“ to „9“)

· the ON/OFF time.

After switching-OFF the cooking zone the respective display

shows “H” until the assigned cooking zone temperature is

mathematically in a uncritical level. (≤ 60°C).

Automatic power OFF function (operating time limitation)

Dependent on the selected setting, every cooking zone will be

switched-OFF after a dened maximum operation time if no

operation of the assigned cooking zone follows within this time

period. Every change of the cooking zone condition (by means

of the PLUS-, MINUS- key) puts back the maximum operation

time of this cooking zone to the initial value of the operating time

limitation.

Cata IT 773 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info