Bedienungsanleitung Caterchef 309.001 - U1 (Seite 22 von 44) (Englisch, Holländisch, Französisch)

646180

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

- 22 -

ENGLISH

Connecting the water supply

Warning

1. The water connections must comply with local safety standards and regulations.

2. The minimum water pressure required is 2 kg/cm

. Cleaning performance will be adversely affected if water

pressure is too low.

The temperature of incoming water must not exceed 65°C, and water pressure must not exceed 5 kg/cm

Connect the inlet hose to the mains water supply (3/4” internal screw thread). Ensure that your hands are completely

clean before you connect the tap or magnetic valve to the mains water supply. The manufacturers will not accept any

responsibility for any damage or loss incurred as a result of foreign objects (e.g. dirt, iron or calcium) entering the tap

or the magnetic valve. Pull carefully on the inlet pipe to ensure that it is ﬁ rmly attached. Open the tap slowly and

check that no water is leaking. It is necessary to ﬁ rst check that the inlet pipe is ﬁ rmly attached and the supply line is

open each time the dishwasher is used.

Water inlet (Requirements for water inlet)

Temperature Pressure (dynamic)

°C °F K Pa kg/cm

With 3 KW (230 V) electric boiler 40 ~ 60 104 ~ 140 196 ~ 490 2 ~ 5

With 6 KW (400 V) electric boiler 10 ~ 60 50 ~ 140 196 ~ 490 2 ~ 5

Water discharge

Connect the water discharge hose to a suitable drainage point. This must be lower that the discharge outlet of the

machine to ensure natural drainage. If necessary, to achieve this, the machine can be raised or placed on the

stainless steel support frame (optional), or the ﬁ tter can install a drain pump (optional).

If local regulations require a grease trap, it must be installed by a certiﬁ ed company.

Note: After installation, test the pressure of the incoming water supply. If the hydrodynamic pressure is lower than

2 kg/cm

, it will be necessary to install a pressure raising pump (from an independent supplier). If the stagnation

pressure is higher than 5 kg/cm

, it will be necessary to install a pressure reduction valve (from an independent

supplier)

Tests

Water inlet hose

Clean the water inlet hose before connecting it. Clean all ﬁ lters after their ﬁ rst use.

Water connection and hydrodynamic pressure

Check that the inlet hose is ﬁ rmly connected. The hose may come loose and start leaking if the dishwasher is moved.

If the hydrodynamic pressure is too low, this may lead to malfunction of the machine.

Electrical connection

Connect up all the wires in the switch box (400V). Check that all wires are ﬁ rmly connected. Check that the other

electrical components, for example the switches and cable, appear to be in good order.

Inspect the inside of the dishwasher

Check that there is nothing inside the machine that does not belong there (for example: clothes, screws, nuts & bolts,

tools, packaging materials, etc.).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caterchef 309.001 - U1 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info