Bedienungsanleitung Cateye CC-CD200N - ASTRALE 8 (Seite 1 von 2) (Englisch)

508114

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

MODE

L(mm)

12 x1.75 935

14 x 1.50 1020

14 x 1.75 1055

16 x 1.50 1185

16 x 1.75 1195

18 x 1.50 1340

18 x 1.75 1350

20 x 1.75 1515

20 x 1-3/8 1615

22 x 1-3/8 1770

22 x 1-1/2 1785

24 x 1 1753

24 x 3/4 Tubular

1785

24 x 1-1/8 1795

24 x 1-1/4 1905

24 x 1.75 1890

24 x 2.00 1925

24 x 2.125 1965

26 x 7/8 1920

26 x 1(59) 1913

26 x 1(65) 1952

26 x 1.25 1953

26 x 1-1/8 1970

26 x 1-3/8 2068

26 x 1-1/2 2100

26 x 1.40 2005

26 x 1.50 2010

26 x 1.75 2023

26 x 1.95 2050

26 x 2.00 2055

26 x 2.10 2068

26 x 2.125 2070

26 x 2.35 2083

26 x 3.00 2170

27 x 1 2155

27 x 1-1/8 2161

27 x 1-1/4 2161

27 x 1-3/8 2169

650 x 35A 2090

650 x 38A 2125

650 x 38B 2105

700 x 18C 2070

700 x 19C 2080

700 x 20C 2086

700 x 23C 2096

700 x 25C 2105

700 x 28C 2136

700 x 30C 2170

700 x 32C 2155

700C Tubular 2130

700 x 35C 2168

700 x 38C 2180

700 x 40C 2200

L mm

SET

ST/STOP

MODE

SET

OKOK

Warning

• Pay attention to the road or trail! Do not be distracted by the

computer.

•Be sure to securely mount the magnet, the sensor, and the

bracket on your bicycle. Periodically check to insure they are

mounted securely and the screws are not loosen.

• Keep batteries out of reach of small children. Dispose of batter-

ies according to local regulations.

• Avoid unnecessary prolonged exposure to the sun. Never at-

tempt to disassemble the computer head.

• Don’t use thinner, benzene or alcohol to wipe the surface of the

computer. They may damage the surface of computer.

Computer Set-up

(For first use or after replacing the battery)

All Clear

Push the AC button on the backside.

* Push the AC button when using this

system for the first time and every

time the battery is replaced.

Set The Tire Circumference

Set the tire circumference in mm.

Note

Refer to the chart shown on the right.

Setting is fixed and completed by pushing the SET button.

Increase the

number

Max. 2999 mm

Decrease

the number

Min. 10 mm

MODE Button

START/STOP Button

SET Button

Contact Point

Measurement Selection

Select the measurement unit, kilometer or mile, by pushing the

MODE button. And fix it by pushing the SET button.

Kilometer

Mile

AC Button

You need to know the

tire circumference

(L mm) beforehand.

You can refer to the

guide chart to roughly

know the tire circum-

ference.

Tire size

Tire size is usually shown on

the sidewall of tires.

Important

Note

Basic Functions Test

Spin the front wheel to see if Speed is reading properly. Push the mode button until Cadence

(Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading

properly.

Note

When the computer does not indicate the speed/cadence, check the position of the

magnet and the sensor.

Lever

Mount The Bracket

Secure the cord on the frame or the fork with the nylon ties 9 and coil it around the brake

cable to lead to the handle bar.

Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the

screw. Slide the computer into the bracket until you hear the click sound. The contact

points are automatically closed. When you need to remove the computer, slide forward the

computer with the lever pushed simultaneously.

Note

Allow enough wire clearance in the area marked with to insure you can turn

the handlebars all the way from side to side without pulling the wire.

Slide

Rotate the front wheel.

Rotate the crank arm

AC Button

Preparation Complete.

(the screen will show the time measurement in this state)

* The auto mode is ON in this state.

ASTRALE8

Installation of the Computer on Your Bike

The computer comeswith the following parts.

Important Note

Mount the magnets 6 (7) and the sensors 3 (4) on the appropriate positions so that

the center of each magnet 6 (7) may align with the the marked line on the sensor

when the front wheel (or the crank arm) is rotated.

1 Bracket

2 Cord

3 Speed Sensor

(short cord)

4 Cadence Sensor

(long cord)

Center

5 Sensor Rubber Pad

6 Wheel Magnet

7 Cadence Magnet

8 Bracket Rubber Pad

9 Nylon Ties (12)

Left Chain

Stay

Please read these instructions carefully before installing or

using the CAT EYE ASTRALE 8.

Please don’t throw away this manual, Keep the manual at a place easily accessible.

CAT EYE ASTRALE 8

CYCLOCOMPUTER CC-CD200

E: Owner’s Manual

Spoke

Crank Pedal

Front Fork

Sensor Side

Within 5 mm

Inward Side of

The Crank Arm

Left Chain Stay

Mount the cadence magnet and cadence sensor.

•Mount the cadence magnet 7 on the crank arm so that it faces the sensor.

•Secure the cadence sensor 4 on the left chain stay with the nylon ties 9.

Mount the wheel magnet and speed sensor

•Mount the wheel magnet 6 on a spoke of the front wheel so the surface of the magnet

will face the sensor.

•Secure the speed sensor 3 on the front fork with the larger nylon ties 9.

Sensor Side

Important Note

Adjust the position of each sensor so they are within 5mm of the 6 (7) magnet.

Secure the nylon ties.

Marked Line

Center

Front Fork

Within 5 mm

Rotate

U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending

CCMCD2-021210 066600250 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-CD200N - ASTRALE 8 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-CD200N - ASTRALE 8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info