Bedienungsanleitung Cateye CC-GL10 (Seite 5 von 28) (Englisch)

508112

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Introduction

How to install the

unit on your bicycle

How to use the

computer

Others

Changing the

computer con-

ﬁguration

Uploading the mea-

surement data

Setup of your

Setting up the

computer

Setting up the computer

Perform the following formatting operation, when you use the unit for the ﬁrst time or re-

store the unit to the condition before shipment.

Caution: All data are deleted, and the computer is reset to the factory default.

* To complete the setting up quickly, press the MENU button twice after the formatting

operation to stop setting up the computer. Then, you can set up quickly using your PC,

by changing the computer conﬁguration using the special software application “CATEYE

Sync™”. For details, see “Changing the computer conﬁguration” (page 20).

Format (initialize)

Press the MENU button on the back of the computer and the AC

button simultaneously. Release the MENU button when a test

pattern is displayed on the screen.

MENUMENU

MENUAC

1 2 3

* When all screen items light up without any test pattern dis-

played on the screen, the formatting operation has not been

completed properly.

Perform the formatting operation again.

Select the speed unit

Select “km/h” or “m/h”.

MODE

km/h

↔

m/h

(Back)

Watch video

(YouTube)

Click the button, then a browser will open and a

video will be played back.

How to turn on/off the power / how to charge the battery

Power ON/OFF

Press and hold the button on the back of the computer for 2 seconds.

* Set up the computer when you turn on the power for the ﬁrst time.

For details, see “Setting up the computer” (on the right of this page).

* When the remaining battery capacity is small, charge it according

to the following instructions.

How to charge

Set the computer to the cradle

Caution: Do not set wet computer to the cradle, for

example after ride in the rain. It may cause

short circuit and damage the computer or

the data.

Insert the USB plug in your PC or a commercial

USB battery charger

Once charging is started, only (battery icon) is displayed.

Icon Description

(Animation) Charging

(Light up) Charging is completed

* When the computer is connected to your PC, the battery can-

not be charged with the PC in sleep state.

* With USB1.0, it takes time to charge.

* The battery charges to about 80% after approximately 90

minutes.

* The standard charging time may change according to the

environment for use.

* The computer can be used for 10 hours on a full charge.

Remove the computer after charging is completed

Disconnect the USB plug from your PC or a USB battery char-

ger, and then remove the computer from the cradle.

* To remove the computer, press it out by hand while holding

the cradle.

Standard

charging time

Approx. 5 h

Test pattern

Battery icon

Cradle

Computer

(press & hold)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-GL10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-GL10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info