Bedienungsanleitung Cateye CC-GL11 Stealth evo (Seite 30 von 33) (Englisch)

602323

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Introduction

How to install the

unit on your bicycle

Setting up the

computer

How to use the

computer

Changing the

computer con-

ﬁguration

Uploading the mea-

surement data

Setup of your

Others

Troubleshooting

The following troubles are not due to failure.

See also “FAQ” in CATEYE Atlas™ (web) (http://www.cateyeatlas.com/qa/).

Trouble Check Items Remedy

Measurement cannot

be performed

(

turns on and

STOP is displayed)

–

Measurement is paused.

Press the

button to start mea-

surement.

For details, see “Starting/Stopping

measurement” (page 10).

The measurement data

is wrong.

–

Measurement may stop, or the

measurements may differ from the

actual value depending on the GPS

receiving status, since this unit

measures using GPS signal.

MEM FULL ﬂashes. Does the maximum re-

cording time or the num-

ber of trips exceed the

upper limit?

* For details, see “Record

interval and capacity

limit” (page 19).

Connect the computer to your PC

to upload the trip data (page 15).

All the trip data transferred to your

PC will be deleted from the com-

puter, and new data will be able to

be recorded.

Does the maximum time

for one trip exceed the up-

per limit?

* For details, see “Record

interval and capacity

limit” (page 19).

Perform the resetting operation

(page 12) to stop the current

trip.

Then, you can record as another

trip.

Trouble Check Items Remedy

When the power is

turned on,

(bat-

tery icon) ﬂashes, and

then no display ap-

pears.

–

Remaining battery capacity is

nearly zero.

Charge the computer according to

the procedure in “How to charge”

(page 5).

The power is turned off

while riding.

–

The power is turned off automati-

cally in 10 minutes without GPS

signal received.

(Auto power off)

No display appears by

pressing and holding

the

button for 2 sec-

onds.

Is the battery for the com-

puter empty?

Charge the computer according to

the procedure in “How to charge”

(page 5).

Incorrect data appear.

–

Follow the procedure in “When the

operation is unstable” (page 29).

Measurement cannot

be performed

(

ﬂashes on the

display).

Is it immediately after

turning on the power?

It may take about 2 to 3 minutes to

acquire the positional information

after receiving GPS signal.

Is it out of the GPS service

area?

GPS signal does not reach, thus

cannot be received in a tunnel and

underground, between high-rise

buildings, under an elevated struc-

ture, etc.

Is the weather not suitable

for receiving GPS signal?

GPS signal may not be received

when it is raining or snowing.

Is the unit installed so that

the computer display (an-

tenna) faces to the sky?

To receive GPS signal effectively,

install the unit so that the computer

display faces to the sky.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-GL11 Stealth evo Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-GL11 Stealth evo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info