Bedienungsanleitung Cateye CC-RD100N (Seite 1 von 2) (Englisch)

471842

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Tire circumference

reference table

12 x 1.75

14 x 1.50

14 x 1.75

16 x 1.50

16 x 1.75

18 x 1.50

18 x 1.75

20 x 1.75

20 x 1-3/8

22 x 1-3/8

22 x 1-1/2

24 x 1

24 x 3/4

Tubular

24 x 1-1/8

24 x 1-1/4

24 x 1.75

24 x 2.00

24 x 2.125

26 x 7/8

26 x 1

(

)

26 x 1

(

)

26 x 1.25

26 x 1-1/8

26 x 1-3/8

26 x 1-1/2

26 x 1.40

26 x 1.50

26 x 1.75

26 x 1.95

26 x 2.00

26 x 2.10

26 x 2.125

26 x 2.35

26 x 3.00

27 x 1

27 x 1-1/8

27 x 1-1/4

27 x 1-3/8

650 x 20C

650 x 23C

650 x 35A

650 x 38A

650 x 38B

700 x 18C

700 x 19C

700 x 20C

700 x 23C

700 x 25C

700 x 28C

700 x 30C

700 x 32C

700C Tubular

700 x 35C

700 x 38C

700 x 40C

29 x 2.1

29 x 2.3

935

1020

1055

1185

1195

1340

1350

1515

1615

1770

1785

1753

1785

1795

1905

1890

1925

1965

1920

1913

1952

1953

1970

2068

2100

2005

2010

2023

2050

2055

2068

2070

2083

2170

2145

2155

2161

2169

1938

1944

2090

2125

2105

2070

2080

2086

2096

2105

2136

2146

2155

2130

2168

2180

2200

2288

2326

Tire size L (mm)

L mm

5 mm

4 5

Pull securely

Remove/install the computer

Spoke

Sensor line

Inside of right

front fork

Stem

Handlebar

Inside of right

front fork

Inside of right

front fork

* Attach between one and three sensor pads 8,

putting them together as required.

* After installation, rotate the front wheel gently to check that the speed is displayed on the

computer. If the speed is not displayed, check that conditions

and

are satisfied.

To the sensor

Cut

Toward the sensor line

When attaching the bracket to the handlebar

Caution:

Tighten the bracket, ensuring that the cable does

not get caught in the stem.

Caution:

Tighten the bracket, ensuring that the cable does not get caught in the handlebar.

The clearance between the sensor surface

and the magnet must not exceed 5 mm.

Attach the bracket to the stem or handlebar

When attaching the bracket to the stem

Wrap the cable around

the front brake cable

Caution:

Turn the handlebar to

make sure wire does

not hinder full rotation.

Caution:

Round off the cut edge

of the bracket band to

prevent injury.

Install the sensor and magnet :

The magnet should pass

through the sensor line.

* You can also use ties 0 (in place of sensor rubber

band 6) to secure the sensor.

Install the sensor

Install the magnet

Click

While supporting it by hand,

push it out as if lifting the front up

* For wing type handlebar or

oversized stem, bracket can be

mounted using the Bracket

Holder and nylon ties. (Option).

How to install the unit on your bicycle

1 Bracket band

2 Bracket

3 Nut

4 Sensor

5 Magnet

6 Sensor rubber band (x2)

7 Sensor hook

8 Sensor rubber pad (x3)

9 Bracket rubber pad

0 Nylon ties (x5)

CATEYE STRADA

CYCLOCOMPUTER CC-RD100N

ENG

Before using the computer, please thoroughly read this manual and keep it for

future reference.

U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending

CCRD10-080924 066600507 6

WARNING / CAUTION

• Do not concentrate on the computer while riding. Ride safely!

• Install the magnet, sensor, and bracket securely. Check these periodically.

• If a child swallows a battery, consult a doctor immediately.

• Do not leave the computer in direct sunlight for unnecessary or extended periods.

• Do not disassemble the computer.

• Do not drop the computer. Doing so may result in a computer malfunction or damage.

• When using the computer installed on the bracket, change the MODE by pressing on the

three dots below the screen. Pressing hard on other areas can result in malfunction or

damage to the computer.

• Never place the computer on a metal surface. If you do, the contact points will conduct

electricity, discharging the battery.

• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the

bracket threads.

• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or

alcohol.

• Dispose of used batteries according to local regulations.

• LCD screen may be distorted when viewed through polarized sunglass lenses.

MODE

MENUMENU

MODEMODE

MENUMENU

MODEMODE

MENUMENU

MODEMODE

Switch the

screen or

move digits

(by pressing

& holding)

Enter the tire circumference

Enter the tire circumference of your bicycle in

mm.

* Refer to the tire circumference reference table.

km/h ↔ mph

Increase

Move digits

(by pressing

& holding)

setting

the setting

Clear all data (initialization)

Press the AC button on the back.

Select the desired speed units

Select “ ” or “ ”.

24h ↔ 12h,

or increase

the value

the

setting

(finish)

Preparing the computer

Set the clock

When MODE is pressed and held, “Displayed

time”, “Hour”, and “Minute” will appear, in

this order.

Battery case cover

Contact

Push!

: Speed unit

: Wheel size icon

When the computer is

mounted on the bracket

Measure wheel

circumference (L) of

your bike

To get the most accurate

calibration do a wheel roll

out. With the valve stem

perpendicular to the ground,

mark the pavement at the

valve stem. With the riders

weight on the bike, roll the

wheel one tire revolution in a

straight line and mark the

ground when the valve stem

is perpendicular to the

ground again. Measure the

distance in millimeters. This

is the most accurate wheel

calibration number.

Cateye CC-RD100N Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-RD100N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info