CATEYE STRADA DOUBLE WIRELESS
CYCLOCOMPUTER CC-RD400DW
0678
U�S� Pat� Nos� 5236759/6957926 Pat�/Design Pat� Pending
Copyright© 2011 CA
CCRD4DW-110930 066600620
3
ENG
Tire circumference
reference table
Tire size
L (mm)
12 x1.75 935
12 x1.95 940
14 x1.50 1020
14 x1.75 1055
16 x1.50 1185
16 x1.75 1195
16 x2.00 1245
16 x1-1/8 1290
16 x1-3/8 1300
17 x1-1/4 (369) 1340
18 x1.50 1340
18 x1.75 1350
20 x1.25 1450
20 x1.35 1460
20 x1.50 1490
20 x1.75 1515
20 x1.95 1565
20 x1-1/8 1545
20 x1-3/8 1615
22 x1-3/8 1770
22 x1-1/2 1785
24 x1 (520) 1753
24 x 3/4 T 1785
24 x 1-1/8 1795
24 x 1-1/4 1905
24 x 1.75 1890
24 x 2.00 1925
24 x 2.125 1965
26 x 7/8 T 1920
26 x 1 (571) 1952
26 x 1-1/8 1970
26 x 1-3/8 2068
26 x 1-1/2 2100
26 x 1.0 (559) 1913
26 x 1.25 1950
26 x 1.40 2005
26 x 1.50 2010
26 x 1.75 2023
26 x 1.95 2050
26 x 2.00 2055
26 x 2.1 2068
26 x 2.125 2070
26 x 2.35 2083
26 x 3.00 2170
27 x 1 (630) 2145
27 x 1-1/8 2155
27 x 1-1/4 2161
27 x 1-3/8 2169
650 x 20C 1938
650 x 23C 1944
650 x 35A 2090
650 x 38A 2125
650 x 38B 2105
700 x 18C 2070
700 x 19C 2080
700 x 20C 2086
700 x 23C 2096
700 x 25C 2105
700 x 28C 2136
700 x 30C 2146
700 x 32C 2155
700C T 2130
700 x 35C 2168
700 x 38C 2180
700 x 40C 2200
700 x 44C 2224
29 x 2.1 2288
29 x 2.3 2326
Preparing the computer
1
Press the AC button on the back�
2
Select “km/h ” or “mph ”�
3
Enter the tire circumference of your bicycle in mm�
Refer to the tire circumference reference table�
4
Pl th co ne th se
ing RESET sensor ID number
screen, then moves to clock setting�
When setting the sensor ID, place the sensor at least 20 cm (ap-
proximately 8 inches) away from the computer
RESET button, the sensor will send the ID when releasing the button�
While setting the ID, the computer is on Standby for 5 minutes� If the com-
puter does not receive any sensor signal, or you press and hold MODE during
StandbyERROR ” is displayed and the ID is canceled� Y
up, but cannot measure� Be sure to set the ID according to “Sensor ID Setting”
on the menu screen�
When the ID has been already set, the original ID is applied if you cancel the ID�
5
When MODE is pressed and held, “Displayed time”,
“Hour”, and “Minute” will appear
Before using
it for future reference.
This device
tions:(1)This device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation�
Modifi The FCC requires the user
that are not expressly approved by CatEye Co�, Ltd� May void the user ’
AC
km/h
↔
mph
Increase
the value
Move digits (by
pressing & holding)
Register the setting
Re
setting
Register the
setting (fi
Move to Clock
Setting when no
ID has been set.
Start the ID Set-
ting (by pressing
& holding)
24h
↔
12h,
or increase
the value
Switch the screen
or move digits (by
pressing & holding)
Cancel the ID or
reset (by press-
ing & holding)
Battery case cover
Push!
When the computer is
mounted on the bracket
km/h mph
: Sensor signal reception icon
How to install the unit on your bicycle
Bracket band
1
Bracket
2
Sensor
3
(Speed/Cadence)
Nut
4
Wheel magnet
5
Cadence magnet
6
S
7
ensor rubber pad
B
8
racket rubber pad
Nylon ties (x3)
9
Install the sensor and magnet
The clearance
net than and for
Cadence, respectively
The magnet faces the sensor zone of the sensor
The distance between the computer
and
sion range,
on
sensor points to the computer
A
T
Adjust and fi
Rear wheel spoke
Left Chain Stay
Attach the bracket to the stem or handlebar
When attaching the bracket to the stem
When attaching the bracket to the handlebar
On *
bracket so that the computer is kept horizontal�
Click
While supporting it by hand,
push it out as if lifting the front up
Cut
Caution:
Round
o t b b t
prevent injury�
B
C
T
B
�
When the condition cannot be satisfi
Loosen the sensor screw to adjust the speed� After adjustment, fi
Remove/ the
computer
After installment, check that the speed C ) is
displayed when turning the crank�
When the sensor ID has not been set, set the ID according “Sensor ID setting” on the menu screen�
Sensor zone
Sensor
Sensor zone
T wh ma ma be in an on th
spoke if the above installation conditions are satisfi
Cadence
magnet
Wheel magnet
Cadence
magnet
Wheel magnet
Cadence
Speed
Sensor screw
For wing type hand or stem brack can
mounted using the bracket holder and nylon ties� (Option parts)
Stem
Handlebar
Measure wheel circumference (L) of your bike
T
pavement at the valve stem. With the riders weight on the bike, roll the wheel one tire revolution in a straight line and
mark the ground when the valve stem is perpendicular to the ground again. Measure the distance in millimeters. This
is the most accurate wheel calibration number
WARNING / CAUTION
Do not concentrate on the computer while riding� Ride safely!•
Install the magnet, sensor•
If a child swallows a battery, consult a doctor immediately•
Do not leave the computer in direct sunlight for a long period of time�•
Do not disassemble the computer•
Do not drop the computer to avoid malfunction or damage�•
When bracket, • MODE below
screen� Pressing hard on other areas can result in malfunction or damage to the computer
Tighten the dial on the FlexTight bracket by hand only•
When cleaning the computer•
Dispose of used batteries according to local regulations�•
LCD screen may be distorted when viewed through polarized sunglass lenses�•
Wireless Sensor
In order to prevent any interference with the sensor signal, the transmission range is designed to
be 20 to 100 cm, in addition to use of the ID code� (This receiving range is only a reference�) Please
note the following points�
T•
T• ID1 and ID2 , can be registered to this unit, which are identifi
The computer •
T
mission range�
Interference may occur
Near a TV•
Close to a railroad crossing, railway tracks, TV stations and/or radar base�•
Using with other wireless devices, or some particular battery lights�•
