Bedienungsanleitung Cateye CC-RD410DW Strada (Seite 1 von 9) (Englisch)

508122

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

CC-RD410DW ENG

Before using the computer, please thoroughly read

this manual and keep it for future reference.

Please visit our website, where detailed instruc-

tions with movies are available and the instruction

manual can be downloaded.

The sensor ID was synchronized with this unit before ship-

ment. It is not necessary to synchronize the sensor ID.

* In combination with the optional heart rate sensor, this unit is

capable of receiving and displaying up to 3 signals of the cur-

rent speed, cadence, and heart rate.

Warning / Caution

• Do not concentrate on the computer while riding. Ride safely!

• Install the magnet, sensor, and bracket securely. Check these peri-

odically.

• If a child swallows a battery, consult a doctor immediately.

• Do not leave the computer in direct sunlight for a long period of

time.

• Do not disassemble the computer.

• Do not drop the computer to avoid malfunction or damage.

• When using the computer installed on the bracket, change the

MODE by pressing on the three dots below the screen. Pressing

hard on other areas can result in malfunction or damage to the

computer.

• Be sure to tighten the dial of the FlexTight™ bracket by hand. Tight-

ening it strongly using a tool, etc. may damage the screw thread.

• When cleaning the computer, bracket and sensor, do not use thin-

ners, benzene, or alcohol.

• Dispose of used batteries according to local regulations.

• LCD screen may be distorted when viewed through polarized sun-

glass lenses.

2.4GHz digital wireless system

Each sensor adopts the 2.4GHz digital wireless technology, which is

used for wireless LAN, etc. This technology practically eliminates in-

terference from any external noise and cross-talk with other wireless

computer users during measurement, and enables it to record and

store highly reliable data. However, it suffers interference in the fol-

lowing places and/or environments, which may result in an incorrect

measurement.

* Careful attention is required especially while checking the sensor

ID.

• TV, PC, radios, motors/engines, or in cars and trains.

• Railroad crossings and near railway tracks, around television trans-

mitting stations and radar bases.

• Other wireless computers or digitally controlled lights.

• In the Wi-Fi environment.

Automatic recognition of the speed sensor ID

The speed sensor has its own ID, and the computer measures in syn-

chronization with the ID.

Two speed-sensor IDs can be registered to one computer, which can

automatically identify two speed sensors once their IDs are registered

in advance.

As a tire circumference is set to the speed sensor ID, wheel selection

by manual operation is no longer required, which was necessary with

conventional units.

* The speed sensor currently recognized is indicated with a sensor

icon ( or ) on the screen.

Procedure of automatic recognition

When the computer changes to the power saving screen, and then re-

turns to the measurement screen, automatic recognition of the speed

sensor ID is performed in the following procedure.

The computer searches the speed sensor ID signal, which had

been synchronized immediately before.

Once the sensor signal is received, the sensor icon for the speed

sensor lights up, and the computer starts the measurement.

When the speed sensor ID signal which had been synchronized imme-

diately before, cannot be received another sensor signal is searched.

When the computer receives another sensor signal, the sensor icon for

the other sensor lights up on the screen, and starts the measurement.

When another speed sensor ID signal cannot be received, the

original sensor signal is searched again.

The computer repeats synchronization through the procedure described

above even if it fails in synchronization for some reason, such as com-

munication failure; in such cases however, it takes time for recognition.

* When the computer does not receive any signal from the sensor for

10 minutes, it will change to the power-saving screen. When such a

condition lasts another 1 hour, it will get into the sleep state.

Switching the ID by manual operation

The speed sensor ID can be forced to change manually, according to

the menu screen “Setting the tire circumference”. Use this operation

in the following cases.

• When the computer cannot recognize the intended sensor signal,

since the 2 registered speed sensors are nearby and both are send-

ing a sensor signal.

• When you want to switch the speed sensor ID immediately.

* Once you switch the speed sensor ID by manual operation, the com-

puter continues to search only the speed sensor ID you switched

when returning to the measurement screen. When the computer

cannot receive any sensor signal in 10 minutes, the power-saving

mode is activated, and the computer changes to the power saving

screen. The computer searches through the procedure of automatic

recognition when it returns to the measurement screen.

CATEYE STRADA

DIGITAL WIRELESS

CYCLOCOMPUTER

CC-RD410DW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-RD410DW Strada Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-RD410DW Strada

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info